after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello DevZone,
For my project I have a number of pins generating interrupts from different sensors.
I've read that GPIOTE IN events consume a bit more current than the...
nrf_mesh_config_app.h at the generic level mesh example contains constants like DEVICE_COMPANY_ID, DEVICE_PRODUCT_ID and DEVICE_VERSION_ID . I've expected those values to...
I try to build your an example Smart Remote 3 nRF52 v1.2 in Keil v5.34 and I have some errors.
In the case of nRF52832_xxAA (Target: PCA63519-SR3_nRF52832_Shield) I have...
Hi,
I'm a beginner trying to understand BLE extended advertising. I have modified the peripheral/ble_app_beacon example to broadcast extended advertising packets with PHY...
Hi,
I am transmiting extended advertising packets and I want to set the flags on the extended header as specified on the bluetooth core specification (v5.3) page 2691 (photo...
I am following the Getting Started directions here: https://www.nordicsemi.com/Products/Development-hardware/nrf52-dk/getting-started#infotabs
Steps 6 and 7 do not work...
I am currently using the power profiler kit ll to see if it is suitable to run power consumption tests in our automatic test system. I am using the python API from https:...
Dear community,
I'm using BM833A chips which contains a nRF52811 nordic chipset. I use a S140 softdevice, for both, beacon sender and central.
I have configured both to...
Dear Sirs,
SDK: NCS version 1.6.0
Board: nrf5340 DK
IDE: SES Nordic Edition V5.50c
Compiled in application core cpuappns
I am a beginner with nrf programming...
Hi all,
we use nRF Connect for Desktop Programmer tool for flashing nRF5340 at production plant. Our Regulatory Affairs & Quality Assurance dept. is asking for a validation...
Sometimes the Power Profiler App does not display the average current and charge values for the Window (see screen capture, below). The values are displayed while the capture...
I'm working on a program using the ble_peripheral/ble_aapp_uart project. While testing the program, it was confirmed that the connection was disconnected after 1 minute 35...
Hi ,
I tried to use the sample code of central and peripheral project "ble_app_hrs_rscs_relay" , to add a new service to connect with light and button peripheral by "lbs_c_init...
Hello,
we are developing a PCB with a nRF52840 in normal power mode. I know that VDD and VDDH have to be shorted in the normal power mode, but due to a layout error we have...
