after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
To the kind attention of Nordic support team,
we are experiencing a very random and rare loosing of existing ble bonding infos (device side). So that to reconnect to the...
We are getting a "No SOURCES given to target: drivers__ipm" error making build fail for our custom board when trying to move to 1.5.0 for official nRF53 production support...
Hi,
I am using NRF52832 with SDK 15.0, SDK Mesh 4.0.
As my knowledge, the OTA speed of Mesh DFU is very slow.
So can I use SDK DFU for faster speed?
Thank you.
Hi
Followed all the getting started instructions given here
https://nordicsemiconductor.github.io/asset-tracker-cloud-docs/v1.5.x/docs/aws/GettingStarted.html
and...
Setup :
Device: nRF52840DK PCA10056
Software: NCS v1.3.99
What I am trying to do:
I have 3 SAADC sequences that I need to run for my application that I wish to poll...
HI,
I'm using the zigbee CLI example as coordinator and have another CLI device for reference as router. With my sniffer I can log the association sequence with the cli...
Hello,
I have a nrf5340 PDK .
The kit does not work right, because i got a several errors.
For example in nrf connect v.3.6.1 the PDK is shown as 000000123456 also in...
Hello Nordic support,
I would like to confirm whether nrf52840 supports only Bluetooth 5.0 features or does it also support Bluetooth 5.2 features. If it supports Bluetooth...
Hello, I am working on Nrf52 mesh network and need to update device via any host mcu or flash connected with the nrf52. But could not find any way to implement it.
If anyone...
I have changed our code that has been running on v1.4 successfully to v1.5
Mainly because I'm hoping for an improvement in the reliability of the new modem library.
However...
Hi All
Can anyone please point me to any documentation/app note that explains how the UE receives a Valid paging message when Network wants to reach the UE. Is there a...
Hallo,
IDE: Segger Embedded Studio
nrf52840 DK
Custom Board with ProteusIII
I have designed a custom board with ProteusIII (nrf52840 SoC) and was working with...
Hi,
I am currently in India city Bengaluru.
as ibasis sim does not support my region so
i am trying to connect nrf9160 to lte network using airtel sim card, but it is...
Hi,
We are working on a new product with " nRF52832 " IC. We want to test our design RF antenna (PCB trace Antenna) performance. For RF test we found an example code and...
If I change the NRF_SDH_BLE_GATT_MAX_MTU_SIZE in sdk_config.h to any value greater than 23, immediately after connecting the stack executes a sd_ble_gattc_exchange_mtu_request...
