Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I am trying to implement the IAS Zone on a nRF52840DK, with reference to the CLI agent example.
How do I get the IASZone.h and zcl_option.h file?
Where do I include...
We want to physically connect our nRF muRata dk (WSM-BL241-ADA-008DK) to the ST Accelerometer eval board (STEVAL-MKI197V1). We are assuming the connection takes place on the...
I want to used p1.01 and p1.2 and p0.13,so how to defined it.
I do like
#define led0 13 to used pin p0.13 its working but how to define pin P1.01 and all
Hi,
I'm using nrf52840 and connecting to a mobile device.
Randomly - I get disconnections with error code 133 - on characteristics write, on mobile side.
In addition...
thingy91:nRF52840 int64_t convert the value to string in sprintf
Add next line in proj.conf
CONFIG_NEWLIB_LIBC=y CONFIG_NEWLIB_LIBC_NANO=n
If you do the following: ...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I am testing a BLE example that transmits 50 times per second (50Hz) using nRF52-DK(PCA10040) and SDK16's ble_app_uart. After making an arbitrary value into a string using...
Dear All,
We are using nrf52480, we our app is simply scanning for Near By Ble, and if the UUID of a ble Matches it send the data to another controller through Lib Uart...
I'm working on an application with SD card, and I've noticed what I think is strange behavior on MOSI. SD has pullup on every pin (10k), per the spec. Whichever pin I choose...
I receive my nRf-9160-DK but decided to try to get the nRF52840-Dongle working first, Simply walk through installing nRFUtil, following the directions I ended up here: https...
Hi
When programming /NordicSDK/v1.3.1/zephyr/samples/basic/blinky in the cpu_app_ns version, it will not start. It is starting when I compile it as a secure application...
In our application we have an RC network (1kOhm-100nF) on pin AIN1. We charge the capacitor with a defined pulse length and then measure the voltage.
At the desired voltage...
Hello,
I can connect to the Segger JLink plus device using USB but when I try to connect to a Segger JLink pro via Ethernet, nrfjprog I receive the following message " There...
Dear Nordic support,
I'd assume it should be OK to allow nrf52840 to advertise in dual phy mode - primary in 1Mbps and secondary coded phy so that phones with and without...
