Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I successfully read accelerometer data at 3000 samples per second . However, when transmitting the data over Bluetooth Low Energy (BLE) , I am only able to send 200 samples...
Is there any pre-existing library similar to the Arduino avdweb_VirtualDelay library available for the Nordic Semiconductor nRF52840 Dongle? I do see the procedure on how...
Hello In SDK 2.6.xx I used to define an extra CMake argument in the VSCode UI, i.e "-DMFG=1" This argument was available when CMakeLists.txt was processed so I could do additional...
We have difficulties to get RTT prints from MCUBoot while performing DFU.
As far as I understand Segger RTT is reinitialized when booting Application and this might be the...
I want to change the bitrate for different settings：
Different settings with 48khz&10ms:
I try ot change the prj.conf to add these:
But an error occurred during...
Hello,
I have a device that I want to operate on the lower range of RSSI (but still around -80dBm and have problems with disconnect. I would like to understand if there...
I want to capture device log. How to capture device log ? Which configuration I need to enable in SDK ? Can you provide sample example which capture device output log ?
We are planning to use NRF52840 for a medical device would like to know from Nordic or anyone from the forum about the verification/validation of SOUP (Software of unknown...
Hi, I am encountering multiple conflicts in the device tree view, which seems quite strange.
"Oscillators" appears to collide with regulator@4000 .
"Clock" appears to...
Hello,
We are in certification stages for our custom product based on the nRF7002DK. Our application requires BLE and WiFi to be operational simultaneously. Consequently...
Hello,
I am new to developing with Nordic products. I have experience working with other microcontrollers like Microchip and STM32. Both of those have their own IDEs. Does...
I would like to integrate System OFF mode of operation into idle system hooks in Zephyr (i.e. when the CPU is idle, it goes into OFF power state automatically). As it currently...
Hi there,
I want to advertise to multiple specific BLE addresses, but I don't know how to implement it with the nRF Connect SDK. Please suggest.
I aim to advertise to...
I am using an nRF52840 and nrf52832 to measure distance, but the reported value is almost twice the actual distance . For example, when the actual distance is 1 meter , the...
Hi,
the nrf45L15 datasheet v0.8 says on page 277 "Note: TWIM and TWIS must use clock pins for both SDA and SCL.".
However in the table 72 on page 795, only the SCL pin...
