after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi there
While doing the GMAP tests for our Bluetooth stack with the HCI UART bridge of NCS 2.7 with SoftDevice running on nRF5340 Audio DK, we've tried using the HCI LE...
Hi,
1. Seems to be a bug, how to fix this error. 2. Repeat example: ncs\v2.8.0\nrf\samples\bluetooth\peripheral_uart
Thank you for all your assistance. Kind regards...
Hello. Both toolchain/sdk are v2.8.0.
It is coding based on the wifi station sample provided.
When I made it in the previous version, I created the configuration, and...
Hi,
I am adding out of tree sensor driver (LDC2114) to nrf9160dk, I follow the Adding an Out-of-Tree sensor driver to Zephyr - Golioth . But when building the configuration...
Hi,
we have created a led driver for ucs5603.c taking reference of ws2812-spi.c. we are using nrf52840 with NCS v17.0
we have set SPI clock frequency at 1MHz and we are...
Hi,
I am trying to write a hex file created by building with the nRF54L15/CPUAPP to the nRF54L15-DK, and check whether it is in DCDC mode or LDO mode using the nrfutil command...
I am using three devices in my Zigbee network:
A Coordinator. A Router. An End Device. When I retrieve the LQI data:
If both the Router and End Device connect directly...
Hi. According to nRF54L Series features page ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/device_guides/nrf54l/features.html ), second-stage bootloader...
I've been using ICMSG's IPC to exchange HCI messages between the netcore and appcore, and using SPI to exchange HCI information between the host and appcore. This setup enables...
I'm working on implementing a Bluetooth Mesh network where each node periodically sends messages containing a single float32 value or an array of float32 values (e.g., every...
Hello,
I update ncs from v2.3.0 to v2.8.0 in matter windowcovering project.
my prj.conf file:
CONFIG_PM_DEVICE =y
CONFIG_PM_DEVICE_RUNTIME =y
CONFIG_USE_SEGGER_RTT...
Hi,
I'm developing a firmware based on Zigbee CLI sample. And I enabled DFU of app core and net core via serial with serial recovery mode.
Using SDK v2.4.2 and nRF5340...
Hi,
I am trying to integrate i2c code in peripheral_uart example from ncs 2.8.0.
I am following the steps as instructed in this exercise:
Exercise 1 - Nordic Developer...
I have nRF Connect for VS Code v2024.11.75 and am using SDK 2.6.1. In Lesson 3, Exercise 1 of the nRF Connect SDK Intermediate course in step 8 the instructions show to open...
I am a long time user of Doxygen and I am familiar with its format. I have been using Doxygen manually in my nRF9160 code and it is working fine. I am using DoxyWizard to...
