Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi
As mentioned in the datasheet, UARTE can operate up to 1Mhz. Is there any special condition/factor to achieve this?
and how fast can a regular GPIO operate?
Thanks...
Computer : Mac Book Air M2
OS : Sonoma 14.5
Hardware : SEEED XIAO nRF52840 Sense
I am building my software using nRF Connect VSCode Extension, while when I select my...
nRF5340 NCS 2.6.1 nrfjprog 10.18.1
My project is based on coap_client and also uses MCUBOOT.
I can program both cores using VS Code, and I notice it splits merged_domains...
Hi,
I am using a nRF9161-DK to flash and debug an external nRF9160 board connected via the nRF9161-DK DEBUG OUT 10-pin connector.
In VS Code "CONNECTED DEVICES", I can...
Hi, I am currently working with the NRF52832 on a custom board that is working with a timer for a particular sleep interval now I have added an external RTC module, and i...
Using nrf9160 with W5500 Ethernet NCS Version 2.6.1
My normal MQTT connection is working fine, but connecting to aws is being an issue. I am getting mqtt -22 error. I...
Hi. I wrote a firmware on nrf9160(SIAA chip), but it doesn't work. On the hardware side, the circuit is same as that of nrf9160-DK, CTS and RTS is short respectively.
If...
Hi,
We are using two nRF54l15-PDF to communicate as SPI, one is in master mode and one is in slave mode. The master device sends a simple array of bytes, the first one being...
Hello,
I'm currently working on NCS2.6.0 and ANT sdk v1.3.0,
I would like to know is it possible to do BLE scanning(without connection) and ANT+ heart rate searching at...
I'm working on getting a radio test example project built for our custom board that is currently in production in order to perform some FCC testing, but I'm struggling to...
Hi everyone, this is more of a programming advice question: basically we have a "registration app" associated with our BLE product which will be used to communicate user details...
Hello,
I've been developing code on nRF9160 for a while. In the beginning everything was straight forward and working just fine also the code was pretty simple. Now like...
I am currently working with the nRF5340 and using NAND flash for data storage. With the current code size, I need to create a secondary partition in the external NAND flash...
