Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, In my project I'm working with a nrf52840 SoC and developing an application based on you'r SDK. I would like to understand the proper way of using the "custom_board.h...
Hello, i´m developing on a custom NRF91 board and i´m trying to access the SPI flash memory on it. When i run the code i get the following error:
<err> spi_nor: Device...
Hi,
I am trying to implement a lightweight file system in my external flash memory (ISSI). After the implementation of file system, I want to store a .bin file and later...
Hi
For a specific project i will need to have ability to monitor some 4G/3g/2G protocol stack L2/L3 messages. Is it possible? is there any documentation regarding this option...
Hello DevZone,
In NCS, we have many BLE Mesh examples that is initialed by:
The first argument is a structure that contains some input and output OOB callback functions...
Hello,
Currently I am implementing the nrfx qdec driver in our Zephyr project using the nRF52840 DK. We choose the nrfx driver as this provides events. I am using the nRF...
Hi.
I have designed a node with NRF52833 with +8db power antenna.But i got some issue in signal transmission over 1km range.Please review my layout and matching circuit...
I have the software installed and I am using the nRF52840DK with Ubuntu 22.04. The uart link is /dev/ttyACM0
When I start wireshark and do a capture on all advertising channels...
Hello,
We are designing a product based on the RAK4630 module that integrates nRF52840 SoC.
Since we are creating a low power consumption and battery operated product...
I am trying to set up the AT library to directly talk to the modem through a uart on the nrf9160DK. But when I enter the commands to test "AT+CFUN?" I just get it echoed back...
I'm working with a Fanstel BT40 module which includes an nRF5340 and nRF21540 FEM. As a starting point I'm using the scan_adv example, which is working out-of-the-box but...
Hi,
I'm using Matter SDK v2.7.0, when I build example light_switch for Board: nrf7002dk_nrf5340_cpuapp with Configuration: prj.conf, I get errors as below:
/opt/nordic...
I have nrf9160 with w5500 ethernet module. I am successfully able to get IP address and connect to mqtt broker created locally on my network. Now I was trying to connect to...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.7.0 SDK: v2.7.0
I have successfully deployed and tested projects that run normally, but when I...
