We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello Nordic Team,
I previously asked about how to configure the internal load capacitance for the 32 MHz crystal on nRF54L, and I’ve successfully applied the solution provided...
Hello Team,
I’m working on creating a custom Matter cluster using the instructions provided in the Nordic documentation: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I'm currently testing BLE Coded PHY by using extended advertising.
I used two nRF52840-DK and nRF5 SDK v17 with compatible softDevice.
I've checked that the...
Hi
We are using the CMakePresets.json file for different variations of our firmware. Since the latest update (2025.4.106) the build configuration interface changed a bit...
I had a project that I made with SDK v2.6.0 and Toolchain v2.6.0 with an Actinius Icarus board.
Today I wanted to continue with my project so I build it and everything was...
Hi, We're using the nrf9160 with ncs 2.7, modem FW 1.3.6 We're trying to send an HTTP request with TLS 1.2. We have provisioned our device and verified the key,cert with a...
We are using SDK 2.4.0 and have enabled MCUBoot to support OTA updates using the dual slot method. I have reviewed many posts and existing tickets and have not been able to...
hello everyone,
I am using the nRF52840-QFAA-R7 (48-pin package) along with the nRF52840-DK development board. I have a question regarding I²C communication. Currently,...
Hello everyone, I am planning to make a wireless keyboard, and one of the requirements is that it has a long battery life, so I am very concerned about the power consumption...
So I've been playing around with some code example to make UART work (which I did eventually) using NRF SDK 5 (v17). However the last version of SES (8.22a) requires some...
Hi,
I still have problems understanding the port and pin assignment for peripherals on the nrf54L15.
I need up to three SPIM, one UART and one TWI. That should work, right...
I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
Hello,
I recently bought a Thingy91x; before that, I was using a Thingy91. I activated it and successfully programmed the Hello nRF Cloud firmware via the Quick Start in...
Hi All,
Previous last two times I opened my project in VS Code it displayed a deprecation notice complaining about SDK and toolchain versions. My plan was to address it...
