Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi,
I'm trying to run the zephyr/samples/drivers/adc/adc_dt example on the nRF54L15 DK .
I modified the board overlay file zephyr/samples/drivers/adc/adc_dt/boards/nrf54l15dk_nrf54l15_cpuapp...
Description:
I'm having an issue with my nRF52811 custom board where the device won't start BLE advertising after programming, but it works after cycling through GDB monitor...
Hello,
Following the NRF54L Express course I see that PWM duty cycle can be updated from RAM via EasyDMA but I can't see an example of how this can be done anywhere...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
When i flash i always get the this error: before this i had an another sensor the VL53L0X which worked perfectly.
[0Sensor device not ready! 0:00:00.254,119] <err> VL53L1X...
We are trying to develop a smart controller based on the nRF54L15 that supports a dynamically configurable number of buttons. We want users to be able to select the number...
Hi,
I’m trying to explore the capabilities of DECT NR+ technology using the nRF9151-DK. Are there any recommended external antennas that I would be able to use with this...
Hello,
we are building a custom PCB using the nPM1300. We need a low-noise 1V8 rail for a sensitive analog component and are wondering what the best setup for that would...
I’m working with the CRACEN peripheral on the nRF54L15 and I’m trying to understand the DMA User Tag field used in registers like `CRYPTMSTRDMA.FETCHTAG`.
The documentation...
Hello,
i'm working on a matter sensor on a nRF52840 Dongle and BME280.
The softaware is based on matter/temperature_sensor with config changes to support nRf52840 Dongle...
We are using the Nordic Semiconductor nRF7002-DK . In this board, both PS-Poll and No-PS-Poll power-saving modes are working as expected. However, when running in TWT (Target...
Hi,
we have a issue to find the right configuration to get the maximum throughput in a multiple connection scenario.
In our setup, we are using one central and three peripherals...
Dear Nordic,
We are performing current measurements on a nRF-9151 DK using the Power Profiler Kit II. The attached picture shows the 9151 and PPK-II connected. Notice that...
