Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Description:
We are using nRF54L15 with NCS v3.0.0 , and the following clock configuration:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL =y
CONFIG_CLOCK_CONTROL_NRF_K32SRC_50PPM...
The standard 802.15.4 message FCF define an Acknowledge-expected bit. It is implied in the documentation that the radio will send the Ack automatically in Assisted mode. 1...
Hi,
I am having an issue with matter device commissioning after updating from NCS v3.0.2 to v3.1.0. Prior to the update, the device was able to join a matter network running...
some days ago, my vs code can run the most jobs for nrf connect. it works well.
but now. I cannot find any valid tools (build debug ....) in nrf connect label in vs code...
The STM32 chip collects audio data with the following audio parameters: a sampling frequency of 44 kHz, a sampling precision of 16 bits, and a single channel. The STM32 chip...
，
HI
I am using the periodic_sync_conn example on nRF54L15. I found that after calling bt_le_scan_start(BT_LE_SCAN_ACTIVE, NULL); , it should be interval scanning.
1...
I am running the nRF70 Wi-Fi BLE Image Transfer Demo: https://github.com/NordicPlayground/nrf70-wifi-ble-image-transfer-demo?tab=readme-ov-file
For the camera and board...
I have been trying to make SAFERTOS based BLE example working on nRF52832 (PCA10040) similar to the one provided by Nordic SDK 17.1.0 at `examples\ble_peripheral\ble_app_hrs_freertos...
The same config I was working with the past months and could still debug yesterday morning is not working correctly since this morning. Mostly when I start a debug session...
As the title suggests, I hope to obtain a peer_manager implemented using fstorage.
I am currently developing the nrf52832 using the nrf sdk version 17.
I rely on the peer_manager...
I am trying to build a firmware for Thingy:53 that simply streams the magnetometer via BLE. I have BLE and Gatt working fine; I can even read and stream the IMU sensor. But...
I have attempted running various Matter sample applications on the nRF5340 DK board using both nRF Connect SDK v2.9.1 and the latest stable v3.1.0 releases.
All samples...
Hello,
I need to detect the end of messages coming through UART. nRF7002 asks requests and the device connected via UART responds. Baudrate is set to: 921600.
It is a...
Hello,
l2_e1 and l2_e1_sol are generated and built no error. They flash, but they don't load the program the nRF52 DK. I used several versions of the toolchain and SDK....
