Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi,
I am trying to measure the current of a custom board using PPK board, My custom board takes 5 Volt input supply but PPK board has a 1.8-3.6 Volt external power supply...
I am trying to modify the nRF52840dk_nrf52840 spi_flash sample, ncs/zephyr/samples/drivers/spi_flash , to use dual QSPI.
Following is my device tree configuration:
I...
I am able to pair a peripheral device using advertising 16bit UUID to the Central Device(nRF52840-DK board).
Also I am able to read the Battery level service and Device...
Hi, I have successfully achieved the OTA DFU function on nRF52805. This is what I can see now:
Step 1) I can see the Nordic_Buttonless BLE signal. After connection, there...
When using the nordic power profiler for the nrf52840, it gives the "idle" current as 2.7uA. Presumably this is the deep sleep current, but it seems like this number doesnt...
I've been using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 for my development. I'm trying to switch to the nRF connect SDK. I'm having a hard time figuring out where to...
Hi everyone,
So Im trying to modify the event handler of the ATT_MTU example file to have it so that it logs every time a byte is sent / instead of KB but for some reason...
Config options for enabling SDHC card support are not working with nrf SDK V1.6.0. Unable to create the project using Segger IDE.
The same options are used with nrf SDK...
Hello,
We are switching our firmware from the old sdk into the NRFConnect zephyr sdk and I cant see any way to retrieve the channel of the advert when scanning. We need...
Hi everybody,
i've got an issue i want to discuss here. I'm building a webserver using the nRF9160DK with ethernet-shield from PHYTEC and an SD-card which holds the frontend...
Hello,
So I was exploring the nRF52840 DK as a Zigbee device when I found this page: Zigbee CLI wrapper .
This seems very promising, having a python CLI to interface with...
Hello,
I'm doing a project with Zigbee using the nRF52840 and I want to read some sensors that talk via UART.
I have ported with success the nrf_uart example but after...
dear all
Can keil compiled library be used in segger embedded studio? For example, I have a paw8001_ ofn114009_ 12_ m4f_ keil.lib
Library, can I put it directly into NRF...
