Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi, I'm developing some products and i need my all devices to synchronize within 10ms difference, using UTC Time standard
Here is basic concept that i want to do for my...
Hi there,
We want to compare the power profile of the nRF9160 with a different device, but for this we want to ensure that both devices are transmitting at the exact same...
We're using nRF5 SDK v16.0.0, FreeRTOS, SoftDevice on nRF52832.
We plan on having two applications in flash. We want both applications to be able to access (read/write)...
Hi,
I am working on BLE 5, I have few queries related to connection parameters
1. Can you tell what is the min PDU size does nrf52805 BLE stack supports with LE secured...
I was wondering in Bluetooth mesh, which layer defines the Relay, Proxy, Friend, and the Low Power features for nodes? For example, is it done by the application, Link layer...
Hi there,
I have nrf52833dk and i have implemented the direction finding examples from nrf connect sdk. kindly guide me about antenna hardware setup that i need to do with...
Hi,
Please excuse me if I ask some stupid questions I am new to wesr and have only used git simply over the last few years. These questions stem from trying to get percepio...
Hi,
I'm designing my own algorithm for direction finding and for that i need IQ value as input. In NCS v1.6.0, in the locator exemple for aoa, the IQ value are store in...
hello,
I'm using SPI in NRF52840 with sdk16, In Nordic Dev zone forum I have read that we can configure frequency of SPIM3 up to 32 MHz but in actually as I can see there...
Hi All,
I am trying to make a project for RGB lights using nRF52-DK using NCS.
In these lines of code I am getting the following error -
'DT_N_ALIAS_rgb_pwm_P_ch0_pin...
Hi All,
wondering if anyone else has experienced this. I'm currently developing a program based off of the ble_hids example in SDK17. Currently I'm using the app_timer...
Hi All,
Setup:
SoC: nRF51822
SDK: 11.0.0
Softdevice: S130 2.0.1
I am facing occasional HardFault and It is happening randomly. I need to test device few hours...
Hi Team,
I am trying to perform firmware update of nrf52840DK using MCUBOOT bootloader over UART. I have followed the link: https://devzone.nordicsemi.com/nordic/nrf-connect...
Hello everyone,
How can I use rand() and srand() functions in NCS?
I have already #include <stdlib.h > , but I got this issue:
undefined reference to `srand'
Thanks...
