Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm trying to get Thread working on the nRF52820. It seems that neither the "nRF5 SDK for Thread and Zigbee" nor the "nRF Connect SDK" support it (yet?), but instead require...
Hi,
I understand that when a peripheral is advertising it is also waiting for connection/scan requests.
Does those requests and responses sent via the same advertising...
Hello!
I'm trying to send a mcumgr packet over uart between the nrf9160dk_nrf9160 and the nrf9160dk_nrf5284.
To do this I have a SMP srv and a shell on both MCUs.
...
How do I get following combination to work:
Nrf connect 3.6.1 power profiler with PCA10040 v1.2.1 + PCA63511 v1.1.0 with external power supply and external DUT
The same...
My error messages in Segger studio are messed up (shown below). Everything else is fine. Can I change the font or something?
[m[K'[01m[Kdev[m[K' undeclared (first use in...
Hello, I have a 52832 using SDK16.0.0, that acts as an advertising peripheral (anyone can connect to it), and as a central, connected with 1-1 bond to a peripheral (a 52811...
Hi, using the Nordic power profiler 2 (PP2) kit to measure the current draw of my nRF52833 DK. I have followed the instructions to setup/prepare/wire the PP2 to my DK and...
In the task, when I do a TWI read via nrf_drv_twi_rx(), in the second iteration of the thread, the driver function returns NRF_ERROR_BUSY.
Is it that the driver takes longer...
I've built a custom board using nRF52832 which uses SDK 16.0.0 and softdevice version s113. A part of application is audio streaming/ decibel calculation and transmission...
Hall Mr. Nordic,
I'm sending a 16bit payload with 51822.
The receiver 24L01 is receiving all perfectly. The receiver 52840 is loosing the first two bytes ...
nRF51822...
Hi,
I'm using nRF52840 as my server and the android mobile is my client. At the client end, I'm using the nRF Connect app. It seems like the 50 bytes of data is taking around...
Hello,
I have an nRF9160 DK board (I believe the version is PCA10090 1.0.0) and would like to use the external flash that comes with this board.
Upon inspection, this...
Hi,
I'm seeking help on debugging the network core with Visual Studio Code. My project is not based on a standard SDK and hence I think VS code will be easier to setup than...
hello!
I have an issue, I need to read data from a Module, then I send that data using USBD..
when I put that code in for(;;) before while(true) the port is activated...
