after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
To the kind attention of Nordic support team,
I'm studying documentation in https://developer.nordicsemi.com/nRF5_SDK/nRF51_SDK_v5.x.x/doc/5.2.0/html/a00140.html where it...
Recently I check back again into att_mtu_throughput example in SDK 15.2. there seems to have some updates than in previous SDK, and I see this BLE_GATT_EVT_DATA_LENGTH is...
Dear all,
I am using the following peripherals in our product.
1. TWI Sensor
2. BLE
3. APP timer (1. to poll a gpio pin & as RTC)
4. SPI flash
5. 2 Edge sensitive...
Hi,
I am using nrf_queue to store data in queue which is inserted with time based interrupt at several milliseconds. Also same data from queue is fetched at bulk.
I am...
Hi,
I have modify a BLE program from ble_app_uart by using SDK 15.3, but the system will crash when I do following test:
Please find attach file for my code.
Step1...
I want to double check current draw in the nRF9160 low power modes and need some help in making sure I know how to do so.
I plan to use an oscilloscope for measuring current...
I hear that the GPS should now work with the onboard antenna of the nRF9160 DK for versions 0.8.5 and later. I also read that the asset_tracker application has been updated...
Hi All,
I'm referring to generic on/off ble mesh example code and we are in the development stage.
I would like to know which pins are used for PA and LNA in the example...
HI
In our application we are using "app_sched_event_put" function but its showing [NRF_ERROR_NO_MEM] when i debugged it please look the screen shot.
The sdk we are...
Hi:
for "ble_app_hids_mouse" example ,it has SWIFT_PAIR_SUPPORTED.
Does HID_keyboard also have this feature?
Could I move swift_pair from "mouse example" to "keyboard...
Hi,
I have an ADC which is interfaced with the nrf52.
The samples from the ADC are collected every 2ms (500Hz sampling rate). I store these samples, and when the number...
Hello, I'm having too long connection times or failed connections with some android smartphones (for example samsung A7). Is there a way to decrease connection times?
I...
Just need a quick confirmation, in S140/SDK15.2, what is the correct to config hvn_tx_queue_size?
I found in some post said it can not be set directly, instead one should...
Hi,
I am developing a central application that will connect to my custom made peripheral device and continuously read a characteristic available on the peripheral device...
