after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi!
I am planning to move sample code of uart.because I port the function of uart to spi sample code.
now i take the SDK14.0.0 and uart sample(examples/peripheral/uart...
Hi, I can make a DFU over BLE with nRF connect 2.5.0 Bluetooth Low Energy, all is OK. I use my nRF52840-Dongle PCA10059 (Serial port: COM19 | USB: Nordic Semiconductor nRF52...
Hello,
I'm using SPI 3 to communicate with a NAND memory. I'm able to go up to 8MHz but not more than that. Do I need to set an array list or use the spi manager.
Is there...
Hi Nordic Support, community,
Recently I started working with the nRF52 dongle, after flashing a hex file via nRFConnect/Programmer applic (version 2.5.running on Windows...
Can anyone tell me where the board / device choices in Eclipse come from, as shown in the screen shot below? I have none.
I copied my Eclipse installation from a working...
Hi all I've already setup my Eclipse environment as described in Development with GCC and Eclipse . Now I want to use the SPI libraries for my example. But I got the first...
Hi
The compiling of standard TWI sensor example is giving me an error with SES.
Please find attached a snapshot of the issue.
Need your help ASAP. Thanks
Ch...
My pcb is nrf52832 based, with SPI interfacing ICM20649 sensor.
- Nordic SDK 11.0
- Softdevice 2.0
I am able to flash example code of SPI based ble_peripheral and mpu...
Hello,
I am using an app_timer on my nRF52840 (SDK 15, Softdevice 140) to keep track of the time on my device. After a specific event, I would like to be able to clear the...
Hi,
I use nRF5 SDK v15.0.0. In my application I need periodically disable and enable Bluetooth because they are wifi also, which connected to the same antenna. Its mean...
I have been successfully using nRF Connect v2.5.0 on Windows with a PCA10056 v0.9.2 to communicate with our target device, a nRF52840 using S140 v6.0.0, nRF5 SDK 15.0.0. We...
I have four button and one external interrupt from GSensor on my demo board, and I use GPIOTE_CONFIG_IN_SENSE_TOG for button and GPIOTE_CONFIG_IN_SENSE_LOTOH for GSensor interrupt...
Hi, I am wondering what cost-effective JTAG debuggers you can use with the nRF52832 hardware using the 10-pin standard debugging header. For example, has anyone used the Segger...
Hi All,
I am using the nRF51822 board and have it connected to a micro SD card shield using SPI.
I have not changed anything in the example file with the exception of...
I have a question.
Two slaves connect one Master.
At that time, Can another Master automatically connect the two slaves ?
I know softdevice110_v7 has connection state and...
