Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
my nPM2100-EK can no longer connect to the PowerUP app.... all was working fine for the first few days, but no nothing.... the problem is the same on my PC and Mac....
when...
Hi Team,
I'm encountering an issue when using scan and STA mode.
When I run the shell example along with my custom board, the scan works successfully the first time. However...
I'm trying to build an HTTPS server application using zephyr http library, but the client connection is always being rejected. Can anyone help?
here is the logs
Hello,
I am working with nRF Connect SDK v3.0.2 on nRF52833 and trying to enable DFU over BLE using MCUboot .
I can see the device in the nRF Connect mobile app ,...
Hi Team,
For my project, I am using nRF 5340 board and using the Zephyr SDK for development. I need to read and write data from/to an external SPI EEPROM used ( MP95P08...
Hi,Team,
I am currently using the nrf54l15-dk to debug NSIB. The version of my NCS is v3.0.2. I referred to this link: https://docs.nordicsemi.com/bundle/ncs-2.9.0/page...
Hi,
We have sent out our product (includes the nRF9160 SiP and an nRF52840) for EMC testing and the test lab is asking for the following:
nRF9160 LTE Cat M1 and NB...
I am trying to set the charge current (ICHG) to 100mA or 200mA using nPM1300 on nRF52832 via TWI (I2C). However, the measured current is always limited to ~87mA, even when...
Dear Nordic Support Team,
I am currently working with the nRF9160 and exploring secure methods to lock and unlock the device without losing the firmware.
At present, I...
Following the instructions from
https://docs.nordicsemi.com/bundle/asset-tracker-template-latest/page/common/getting_started.html
I get build errors building the asset...
Hello Team,
We are currently working on the nRF54L15 platform and using nRF Connect SDK v3.0.2. We've successfully added support for DFU over BLE using the following steps...
Hi, I am working on a project where ECG data can be send wirelessly. For that I am using ADS1298 and nRF52833. I am very new to it. I have connected the nRF52833 SPI lines...
Hello all,
I'm using nRF5_SDK_17.1.0_ddde560
Examples folder:
...\nRF5_SDK_17.1.0_ddde560\examples\peripheral\twi_sensor
...\ble_peripheral\ble_app_blinky
Are...
Hi, I created a blinky sample for the ProMicro board. Entered the flash mode as mentioned in https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/boards/others/promicro_nrf52840...
