I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
We were testing MCUboot uisng nRF52 Dev Kit and ran into an issue that updated firmware in slot1 couldn't be booted:
Since we don't need bootloader upgradability,...
Hi,
I upgraded my nRF5340 Audio application from NCS v2.5.0 to NCS v2.7.0 to be able updating the network core.
I noticed that in NCS v2.7.0, the nRF5340 Audio application...
Hi,
I am currently developing a project using the nRF52810 as my controller, with SEGGER Embedded Studio (version 5.42a) and SDK version 17.0.2 as my development environment...
Hello and thanks for reading. I am working with the NRF5340DK and Zephyr (SDK 2.5.0).
As our project has grown, we can no longer fit all our code and MCU boot in the internal...
There are receivers and repeaters with nRF52832 mounted on the board.
When updating with DFU from iPad, a version check error occurs in the customer's environment.
The...
My lipo battery is at 3.86V and I measured 3.76V at VOUT2 which supplies the nRF52832. I just based the design in the example circuits in nPM1300 datasheet. I already reviewed...
Hi Team,
We are using nRF9160
We are provisioning our devices to nRF cloud for more then a year now with a script that create CSV and upload it to cloud during manufacturing...
Hello,
I'm using iphone 15 and nRF52840 board, working on Lesson 3 Exersise 1 solution. In the step 5 after reseting the board there is no logout info on the terminal. But...
HI
When working on the NVS sample on a nrf9160 DK , I noticed the option CONFIG_REBOOT=y
However, it is not clear to me why this option is selected in this sample and...
Hi,
I'm a bit confused regarding the DFU process for the nRF5340: Under what conditions would the interface between the application core and the network core change?
I...
I am using the Nordic Semiconductor Power Profiling Kit II to measure the interval time of a periodic activity of a target device by monitoring the power consumption and measuring...
Our system has SPI and I2C. Each of these communications works in isolation, as implemented in our program, for multiple transactions. When we try to include both we noted...
On p. 62, section "5.3.10.1 Device startup times" of nRF52805 Product Specification v1.4, the startup time of the nRF52805 is discussed as a function of the capacitance to...
Hello,
We use nrf-connect-sdk v1.9.1 (Zephyr v2.7 LTS)
We have a set of network devices. Both routers as sleepy-end-devices.
The sleepy-end-devices connect to the...
how to set bt tx power in NCS
I referred to this example "hci_pwr_ctr", but err occurs:"Set Tx power err: -5 reason 0x00", Possible errors are BT_SCI-ERR_SUNKNOWN_CMD。 ...
