Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi, We are seeing some odd behavior when running in the peripheral role connected to a central device. Occasionally, it appears the central device needs to retransmit a packet...
Does the SPIM of nrf52833 support the selection of SS pulse mode? The SPI of STM32 supports specifying the data bit width by the hardware pulling up the chip to select the...
Hello All,
I implemented the HTTPS call to Amazon using the certificate, and the POST request returns the device ID. Like you docs: Exercise 2 - Adding TLS to the HTTP connection...
HI
My current system consists of an nRF54L15 paired with an external flash and sensor. In low-power mode, the current consumption is approximately 15 µA. After sleeping...
Hello! I am facing issues when trying to set up a PPP connection using the Serial LTE Modem (SLM) application on the nRF9151 DK, and I would appreciate some guidance. I am...
Hello,
I have seen many topics regarding the SAADC sampling modes and power consumption trade-offs on DevZone, but none of them clearly address my concerns. I would like...
Hi there,
We are currently developing a system, where around 480 kbytes of data are transmitted over BLE. Throughput is supposed to be as high as possible.
We are using...
I have a school assignment revolving a technological product, where i need to ask a few questions to a business about their involvement with the product. Therefore i need...
I set the voltage at the PPK “Source meter” to 1250mv, and then used a multimeter to measure the voltage between the PPK “vout” and “GND”, which was 2830mv. How can this situation...
Hi,
We're working on a cellular design using the nRF9151 with an nRF7000 for location finding. We have a working prototype on the Thingy91x and are currently focusing on...
I was reviewing the Large scale Bluetooth mesh testing - Blogs - Nordic Blog - Nordic DevZone and noticed the statement: " Initialize the network by flashing the test firmware...
I want to connect Waveshare E-ink display to nRF5340 using e-Paper Driver HAT. At first, I tried to make all the calls by my own, just by rewriting the code from the ESP driver...
I am attempting to use the COMP section to build a relaxation oscillator. There appear to be a number of interactions between sections, some of which are subtly documented...
Hi there,
I went through all the documentation and instructions in order to use my nRF52DK as a sniffer and I can not see it in the capture devices in wireshark.
am not...
1. What versions of GSMA specification does nrf9160-SICA modem support? In particular we are interesting in SGP.02, SGP.22 or SGP.32 versions.
https://www.gsma.com/esim...
