Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi, I am trying to sound two reflectors from a single initiator, and since the CS works on a one-to-one ACL system, I wanted to know how I can reset the CS-related stuff in...
Hello,
On my board I implemented an RS-485 interface using the ST4E1216IDT transceiver. The DE (Driver Enable) and RE (Receiver Enable) pins are tied together and connected...
Hi Nordic Team:
I am developing the firmware for nRF54H20 using NCS v3.2.0. I need to quickly configure 16 GPIOs as input with pull-up resistors, so I adopted the coding...
I want to highlight 2 infuriating bugs in nrf connect SDK. I believe it applies to all versions.
1) If you have more than one app in your applications tab, the context will...
Hi I would kindly ask what is the recommended layer stack up for npm1300 PMIC.
In reference designs 4 layer board with 2 internal ground planes is used. Looking at the docs...
Using:
NRF9151
TF-M enabled
NCS 3.2.2
I'm trying to find more space for my heap on the nrf9151 and I'm disappointed that with a minimal implementation of TF-M...
I am currently working on a project where I intend to use an nRF54 chip as a BLE or ESB receiver node to capture JPEG image signals and transmit them to a PC via USB. I would...
hi
After switching the 9160 crystal oscillator to an external crystal oscillator, we found that the power consumption of the MCU increased by approximately 1.2 mA constantly...
Hello,
I created a copy of the nRF Cloud CoAP Device Message sample application for the Thingy 91 X. It builds using the default optimization level. However it fails to...
Hello,
Is there any AT command to enable/disable HW Flow Control RTS/CTS for nRF9151?
I tried AT+IFC=0,0; AT+IFC=2,2; AT+IFC? commands but getting error.
Thanks
Hello,
I come today with an issue that was already reported in other tickets such as:
https://devzone.nordicsemi.com/f/nordic-q-a/126189/nrf54l15-grtc-syscounter-resets...
Hi,
I am using nRF5 SDK v17.2.0 on a legacy product. I have code that looks like this:
When reading the characteristic repeatedly, I sometimes see something like this...
Hello everyone
I am following BLE tutorial on Nordic DevAcademy Last part of BLE shows you how to use the nRF52480 to have a BLE sniffer in the Wireshark I have installed...
It seems like the nRF54LM20-DK is not properly powering LED 0-3. After measuring 0V from TP1 to GND, I opened the board configurator and tried applying "ledcontrol" as both...
