Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I am currently working with Trusted Firmware-M (TF-M) on an nRF device and trying to understand the design difference between Internal Trusted Storage (ITS) and Protected...
I have encountered a problem with I2C bus on the nRF54L15. BMP390 sensor is connected to nRF54L15-DK by the i2c bus. if i try to brake the line and recover it agane, the connection...
In nRF5 SDK, we configure GPIO wakeup sources for System OFF using `nrf_gpio_cfg_sense_input(pin_number)`.
What is the **exact equivalent API/configuration** in **nRF Connect...
Hello.
I'm trying to use a nrf52840 as a central device and connect to a gopro13. The connection works a certain number of times. But after a while (several days or maybe...
Hi all,
this is a bit embarrassing, I updated from nrf SDK 2.5.0 to 3.1.1 and I'm a bit lost with the simplest things.
I need to toggle an LED on a custom board. I'm using...
We are using part nRF52840QF (QFN package, not aQFN) as part of new designs as it has the following improvements compared with the nRF52832:
Output power of +8dbm
Extended...
Hi,
I’m having trouble getting the Matter Test Harness to run.
Environment
rPi 5 set up per Matter Test-Harness User Manual.pdf (using project-chip/certification...
Hi, I'm trying to install modem fw using the script given by Sigurd : https://devzone.nordicsemi.com/f/nordic-q-a/53208/updating-nrf9160-modem-firmware-through-the-command...
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
Hi. I have a new project using zephyr 3.5.0 and ZMK, so I don't think NCS SDK is an option. I am using pca10056/nrf52840dk
I am trying to configure I2S, and the examples...
I am currently experimenting with the nrf9151DK and was hoping to mimic a LTE-M sensor that would wake up once an hour, send a message over CoAP with DTLS, then go back to...
Hello, I have problems in the async-mode with the UART21 output and the nRF54L15. I am using Toolchain v3.1.1 and SDK v3.1.1.
When I use the uart_tx function to print out...
Hi
Is there a specification of running the nRF21540 in Tx mode at 10 dBm and 20 dBm with no load connected? Will the reflected signal cause damage to the PA and if yes,...
Hi Support Team
I tested matter bridge sample running on the nRF7002DK with peripheral_lbs sample running on the nRF54L15DK.
Application guide
Then I encountered problems...
I am working with the nRF9160 DK (PCA10090) and would like to use the onboard nRF52840 interface MCU as a host controller for an external peripheral.
From my understanding...
