Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Hello Nordic Team,
I am trying to flash the existing BLE light example code in nRF connect sdk to my BL653 kit with Segger Embedded Studio. The node is not getting detected...
Hi.
I'm facing an issue following this guide ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager-wtih...
I am using running "ble_app_uart_c" example in my Central nrf52 DK board and ruuning "ble_app_uart" example in my peripheral nrf52 dk board..
IF I am sending ASCII values...
Hi,
I'm working on a multilink central device with SDK16, nRF52832.
I'm trying to connect the central to 2 peripherals with certain address. So I added 2 address filters...
Hi all,
I have a nRf52832 Buttonless DFU setup and application is BLE APP UART.
nRF52 SDK = 17.0.2
I need to send a hex file of STM32F4 through UART. Do you have any...
Hello
I'm using sdk17.0.2. And I'm using the ble_nus service with the addition of nrf_crypto (AES_CTR).
I originally used nrf52832 and pca10040 and the test went well...
I just got a new nrf9160DK rev 0.15.0. While plugged in to USB and the switch in the off position, my meter reports 4.95V and 0.016A. Why is this happening? My older rev 0...
From the product spec, the voltage accuracy is listed as -10, +5% from the programmed value. We're using 3.0 V. For our application I need some more specifics on this regulator...
Hi,
I'm building DFU secure_bootloader with oberon crypto library as mentioned here https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts...
Hi,
I'm developing an Android app using the nRF Mesh Library. I have a scenario in which a few phones need to be provisioners given that these will configure new nodes...
prj.conf of light demo:
Can you tell me where CONFIG_LOG is enabled? It is inconsistent with ncs1.5.0. When I enabled CONFIG_LOG_BACKEND_RTT, I was notified of an...
I am trying to program a PCA10059 USB dongle which requires it to go into DFU mode.
I have tried pressing the white button when it is plugged in, and I have tried holding...
I can't seem to find the answer here - sorry if it has already been answered. We were having an issue recently where the root cause ended up being that we were trying to do...
Hi Nordic team,
I noticed that SAADC driver is consuming most of the power in Sleep state. In my application, the processor is in SYSTEM OFF state for 80% of the time (runs...
