I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
One last issue to crack. This one has been in production for a while and hasn't caused any issues other than a little annoyance to the customer. By my measurement when RTC...
Hello,
In regards to the nRF Connect SDK...
I am looking into the possibility of switching out the current implementation of AES used by the Bluetooth firmware. I am curious...
the pin for XL0 and XL1 is P00 and P01
but in my project, I need P00 and P01 works as UART.
I set the parameter to start inner RC clock.and find that: LFCLKSTAT show the...
my costom board is based upon the BT840F fanstell board. I know that this board is based on the nrf52840 QIAA SOC. but I also understand that nrf52840 QIAA has different configurations...
I am working on custom hardware with an nRF52840. I have added the MCU boot in my earlier development as well but this issue I have never faced before.
Problem statement...
Hi,
iam trying to write the data in nvs which i give input through GATT.i can read and write in nvs when not using gatt,BT.
I have 2 codes,1 is working but without GATT...
Hello,
Board: custom board
Soc: nRF52840
SDK: nRF Connect SDK v2.8.0
I would like to know device mac address and use the mac address in advertsing.
can you please...
This page (v2.8.0) https://docs.nordicsemi.com/bundle/ncs-2.8.0/page/nrf/app_dev/device_guides/fem/fem_nrf21540_gpio_spi.html
Suggests copying the following into devicetree...
I am trying to get std::vector to work on nRF52840 running Zephyr in Visual Studio Code running v2.7.0 toolchain , but have been unable to do so. I found some similar tickets...
Hi nordic
I've try to enable 115200 baud UART on p0.9 and p.10 but I can't make it.
I just saw a thread about 52840 can't use 115200 uart at p0.9, p.10:
https://devzone...
Hello,
Is it possible to use the filtering options provided by the nRF52840 BLE sniffing firmware for Wireshark, in Tshark? Specifically the device address filtering....
Hello, I have two questions. 1. First, are these pins reserved in the SOC level or DK level? this if from the nrf52840dk device tree. meaning, if I have a custom board, should...
