Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi Team,
I try to design a PCB based on nrf52840 chips, can you help me check if it is right?
Something like Power supplement, SPI interfaces, and debug and programming...
Hello,
I am currently using nRF Connect SDK v1.7.1 with a nrf9160DK. I keep getting "create_nordic_project.py filed (1)" when I try to open a new project with a overlay...
Hi, I am trying to measure power consumption (the device is an nRF52840 dongle) and I get different results when the board is connected or not to a JLink external debugger...
HI
I need to port my application from NCS v1.5.0 to NCS v1.7.1 Here, I have already tried to transfer my ble application to a higher version. I can't able to do pristine...
@Nordic Semiconductor General Chip nRF9160 rev2 Voltage 3.7 PSM Periodic TAU 5.0 hours Periodic TAU timer element "00011110" Active time timer element "00000000" RRC connected...
Hello,
I have implemented a somewhat working RX algorithm for receiving data over UART but I'm looking for a good way to make it more robust. I haven't found any good answers...
Hello,
I'm try to follow the instructions for multi image example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html#ug-nrf5340-ses-multi...
Hello
I have 2 custom boards both with nRF82532. One is central and the other a peripheral. I use LESC. When no bonding information is stored in either of the devices, pairing...
Hello,
I am using mfw1.3.0 and NCS 1.7.0 developing an application on a custom board implementing the NRF9160 and NRF52820 (The 52820 is put into very low power using nrf_pwr_mgmt_shutdown...
Dear Nordic,
we need to save few bites (product serial number, few settings). we use BLE with bonding on a FreeRTOS based FW. PM is already using FDS, at it is not clear...
Hi,
We made a custom board with nRF52 and it's BLE radio doesn't advertising, not visible on nRF connect APP. RTT viewer is not showing any thing.
We used WLCSP package...
We have developed a small PCB that connects with some other HW. The integrated nRF52840 runs in HighVoltage-Mode and its required to set VDD to 3.0V. The question - how to...
Hey when i try and run my code runnning which is running the SAADC and transmitting data when its connecting with BLE but i can only get around 10 reading before i get a connection...
NRF51422 Custom board
SD310 v3.0
Phone: LG K8 4G
Android 6.0
SDK 9.0.0 Boot-loader example
I am testing over the air DFU with our custom device.
a.) DFU...
