Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
I recently purchased a Thingy91, and here's what I’ve done so far:
Built the firmware
Registered the SIM and device on the cloud platform
Built the Asset Tracker...
I found a related post ( ) where the advice was given to just get a DevKit, which I agree with for development, but my understanding is the nRF52 dongle firmware contains...
MCU : nrf52840
SDK : sdk_17.1.0
Hello, we are developing a product using the nRF52840.
However, we have observed that while the nrf_log_backend_uart~ function is operating...
Dear Nordic support,
I've done some testing to send many data in BLE notifications, and I have a question regarding the BLE stack implementation. We are using NCS v2.6.1...
Hi,
I combined the throughput example and the lbs example in NCS v2.6.2 running in NRF5340DK. It seems the advertisement is not resuming after i disconnect the app (NRF...
I'm trying to install the 2.7.0 toolchain into D:/NCS/ somehow the toolchain manager frequently installs in a different path than the one specificied in the extensions settings...
Hello, guys
I have nRF9151-dk running Serial LTE Modem (SLM) app on it and want to test the ability of working with sockets (open socket, send/receive data, close the socket...
Hi all,
We have designed a custom board including a NRF52805 chip. We also followed PCB design guidelines and used the exact PCB layout recommended by Nordic. As expected...
Hi folks, thanks in advance for your support.
The thing is that in my SEGGER project I didn't have explicitly linked a bootloader to be flashed in the device (nRF52832)...
nRF52832 & NCS v2.6.1
I merged the NUS central and NUS peripheral FW into a single one where the user calls appropriate initialization functions to activate whether central...
Hi,
I am trying to write a simple application that uses I2C on a nrf5340 DK, assigning SCL to P0.9 and SDA to P0.10, using the app core ns . The application builds without...
Hello,
I am working with the nRF9160DK and the Thingy 91 to do some basic evaluation.
I was wondering if these devices supported Private LTE connections.
Thanks.
On Seeed Xiao nRF52840, I'm attempting to use reset (P0.18) as GPIO in a Zephyr (ZMK) app.
I've set
```
&uicr {
/delete-property/ gpio-as-nreset;
nfct-pins-as...
We want to be able to toggle between 128 MHz and 64 MHz on our nRF5340 based custom board depending on whether our audio pipeline is in process or not. However, a note in...
I am facing a similar issue described in https://devzone.nordicsemi.com/f/nordic-q-a/97084/direct-xip-mcuboot-both-images-have-the-same-version where mcuboot is unable to...
