Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
I am experimenting BLE nrf52832 to Ultra low power consumption during advertising , connection and transferring data and also main thing is in ultra low power Mode....
I've recently setup SEGGER embedded studio to program an NRF52832 board and have had issues running the BLE examples.
I've been mostly working with the ble_sdk_app_beacon_main...
Hi,
I'm using the provisioner mesh example for the nrf mesh sdk but when I'm trying to provision (an other board with light switch client example also from nrf mesh sdk...
Hi,
We are developing an audio tranmission code with the mSBC encoder and decoder by using nRF52840 and referring to the smart remote3 example code.
In that smart remote3...
Hi,
As I understand it, LLPM does not currently work on nRF5340 reliably at all (is that correct or does it work well if 1ms interval is increased to something larger?)...
I am using "nRF connect SDK" to implement BLE mesh on BL653 development board, Can you kindly suggest what changes/configurations in "nRF connect SDK" have to be made to run...
Internal fault[0xb3b91b:5060750] occured during linking when disable the log output by [#define NRF_LOG_ENABLED 1],
but no error occured when eanble the log output by [#define...
I know there are other (long!) threads about PDM mics and I've studied them all carefully. Unfortunately I'm still having an issue with our on-board mic. The difference is...
Hi,
Toolchain manager is failing to download SDKs.
I am using:
Windows 10 PC
3.7.0v nRF Connect Desktop application
0.9.3v Toolchain manager.
Downloading sometimes...
Where is the provisioning configuration data getting stored ?
1. EEPROM
2. Any other non volatile memory
Is it getting stored in external chip to nrf52833 or inside...
Hello there!
I'm quite new to the topic and just tried to dig into it a bit, so I'm sorry if I didn't get all things yet about the nRF5280 Dongle :) .
Right now, I'm following...
Hi all,
Using the thread CLI example (on a PCA10056 board) as a starting point I would like nodes to connect automatically to a thread mesh when booting. I then want to...
I use the following example source code to test NFC pairing.
Example source code for NFC: nRF5_SDK_17.0.2_d674dde\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\experimental...
Hi
thank you very much for your paying attention.
Yes the peripherial_uart sample seems to be a good choice for my project. But Uart 0 pins didn't come out on GPIO connector...
Hi,
We are trying to create a network using 20 movesense sensors and BWG840 Fanstel gateway acting as the central. The gateway is running a modified ble app uart multilink...
