We are finishing up a project with the nRF52832 based on the Nordic Thingy. Most of what we want it to do are normal functions of the Nordic Thingy. It connects to a mobile...
I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hello,
I have set up the light and light_switch BT Mesh examples on my nRF52840DKs. I have used the nRF Mesh app to provision them successfully and I can see that they work...
Hi,
I am using NRF Connect environment and would like to enable by program to use MCU Boot functionality with dual-imaging support and FOTA updates.
My Kconfig.sysbuild...
I need to change the path of ncs. after try sometimes, I failed. So, I need remove all the settings and retart my work from initial status. I uninstall vs code. and install...
Dear Nordic Team,
I am trying to configure logging through J-LINK RTT for my firmware.
My prj.conf contains the following:
CONFIG_PRINTK = y
CONFIG_CONSOLE ...
My current product uses the NRF523840 with CODED_PHY periodic adverts. I want to improve the range.
I'm considering a +14dBm (SAR limited) product variant with the NRF54L10...
The nPM2100 datasheet (v1.0) states in multiple areas that the VOUT pin is discharged when the device enters Hibernate mode (and certain other modes).
Is this discharge...
Hi
It seems that the default minium DTLS handshake timeout is about 1 second. That means, there is a retransmission if a response isn't received within this timeout. In...
Hi there,
I am trying to program my custom board hosting a raytac mdbt53 module (powered by a separate USB cable). I have to use the custom connections in P20 connector...
Description: We are working with nRF54L15 connected to an external flash memory MX25R64 . Our setup uses MCUboot with a secondary partition located on the external flash....
Description:
We are using nRF54L15 with NCS v3.0.0 , and the following clock configuration:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL =y
CONFIG_CLOCK_CONTROL_NRF_K32SRC_50PPM...
The standard 802.15.4 message FCF define an Acknowledge-expected bit. It is implied in the documentation that the radio will send the Ack automatically in Assisted mode. 1...
Hi,
I am having an issue with matter device commissioning after updating from NCS v3.0.2 to v3.1.0. Prior to the update, the device was able to join a matter network running...
some days ago, my vs code can run the most jobs for nrf connect. it works well.
but now. I cannot find any valid tools (build debug ....) in nrf connect label in vs code...
The STM32 chip collects audio data with the following audio parameters: a sampling frequency of 44 kHz, a sampling precision of 16 bits, and a single channel. The STM32 chip...
，
HI
I am using the periodic_sync_conn example on nRF54L15. I found that after calling bt_le_scan_start(BT_LE_SCAN_ACTIVE, NULL); , it should be interval scanning.
1...
