Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
Hi dear engineers,
I have a strange TWI problem on my production protype which programmed based on the official twi example with softdevice s130_nrf51_2.0.1 and SDK 12.3...
Hi,
I'm trying to schedule few events within the shortest connection interval . Is it possible to shcedule 3 events, 2.5 ms long within 7.5 ms connection interval? Could...
Dear all,
I am using the nRF51822 custom developed board. Earlier it was working fine, but now when I try to connect the BLE with nRF ToolBox APP UART service, the APP...
Hi,
Have flashed an early sd_power_system_off first line in main() when measuring power-consumption...
Now the SWD access seems gone. Is there a trick to get it back in...
Hi, I'm working on a custom board with a nRF52840.
I want to use REG0 and REG1 as mentionned in Figure 13 of the datasheet : with VDDH, and both DCDC. My PCB is powered...
Hi there
I have a NRF52 Dk already and it had been setted as master.
The log might contain the specific advertisement channel power or how much packets has been sent...
Hello,
I want to send 6 bytes of data over BLE. I will set a timer for this purpose. When there is timer interrupt, the data will be send.
What I wanted to ask is that...
Greetings,
Trying to fast-track my set-up and use of the Nordic Semi devices and toolchain. My questions/comments are as follows:
1 - What is the best *free* option for...
Hi,
I am using ble_app_uart service in my application. I am trying to send files using teraterm tool. If I am sending .txt or .doc files there is no disconnection in the...
Hi,
I am using nrf52832, and measure the power consumption , I found that when I use application timer "after" nrf_sdh_disable_request(), the power consumption of system...
Hello,
i am working on a nRF52840-Preview-DK with SDK 15.
When sending data out on UARTE1 with function nrfx_uarte_tx(..) everything works as expected but only with data...
Hi,
We are using nrf51822 QFAAH00 with SDK 110 v8.1.0 in our project, the application will hangs or not work when control stuck at address 0x6b0 (sometimes at 0x640) programmer...
Hi Nordic team
I would like to have golden version BLE DK as a BLE receiver.
Is the NRF52 compatible with other brand BLE DK or market product?
As I know the BLE device...
