I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
I made a custom PCB with the NRF52840-CKAA and the same 8MB flash memory chip as the PCA10056 NRF528040DK
I used the MX25R6435FZAIL0 because the MX25R6435FZNIL0 was not...
Dear Nordic Team,
After gaining experience with 3G and later 4G LTE-M over the past few years, I have observed a significant gap in the deployment of LTE-M in many countries...
In my NRF52840 based device using NRF5 SDK 17.1.0, I notice that sometimes this loop in the nrfx usbd driver code of the SDK doesn't finish:
[modules/nrfx/drivers/src/nrfx_usbd...
How can I please analyse the latency, reachability and throughput of the DECT NR+ on the nRF9161-DK. I urgently need a solution please, it's for my bachelor thesis. Thanks...
Hi, Im designing a custom board using a NRF9160 MCU. From the product specification it operates at a voltage range of 3.0(2.8)-5.5V. I want to use a 3xLI socl2 3.6v (parallel...
I created a blinky example in zephyr and created my board with Create a new board The build goes well and runs well. The problem is that the device tree gui does not run and...
Hi,
SoC: nrf52840 Environment: nRF Connect SDK v2.4.1
When performing OTA app upgrade all settings and bonds are gone. Settings subsystem seems to be working fine. Settings...
Hello,
I am currently working with the NRF52840 Dongle and have integrated a W25Q512 QSPI Flash chip, connected to the following pins:
CSN: P0.17
SCK: P0.20
IO0...
Hi
I want to know how to get a configuration of a single pin .
I added this function to the blinky example.
But it keeps reporting -ENOSYS.
Testing environment:...
Hi,
I have an application based on the "peripheral_uart" sample code (nRF52840DK, NCS2.70)
As I use interchangeably the same pins as GPIOs and UARTE1, I use UARTE1 with...
Hello,
I been struggling with this issue for a couple of days and can't manage to find the reason behind it.
About the project:
We are developing a IoT device firmware...
Hello all,
i have a problem and I hope that someone can help me.
I can change the bluetooth address of the device with the following code:
and this is okay.
I have...
I work test program on ncs2.8.0.
I put a reference to the BOARD variable at the top of my project's CMakeLists.txt.
When "west build -b nrf52833dk_nrf52833", BOARD is...
Can 52840 dongle program as BLE adapter for development usage like the following URL? Just for development test, so I don't need to buy one.
https://www.amazon.com/ASUS...
I am trying to build the Peripheral UART sample in nRF Connect SDK v2.8.0 targeting the nRF52805 SoC using VSCode. The sample is too large for the nRF52805 flash (linker overflow...
