Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hello forum ,
here i m using nrf52840 where it is customized board ....i tried to print jedec number for windbond w25q64 here this code prints the jedec number and also...
I am trying to interface the PDM mic (Link : https://www.adafruit.com/product/3492) with NRF52832 Devkit. I am using PIN 27 and 26 for Clock and Data Respectively. I can see...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi Nordic Semi,
Instead of using NRF52 for previous projects, I am new in NRF54L15 and zephyr.
I have started the blinky pwm sample in VSC and tried a lot to just...
Hey
Do the hardware in the NRF5340 support what is needed for Bluetooth classic.
I do know that there are no software support and no plans for supporting it, but if...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
The documentation for the QoS dynamic parameters command "+CGRQOSRDP" specifies that the uplink and downlink maximum bitrates are in units of kbps, with a maximum value of...
Hello,
we are using the direct test mode example of NCS with an nRF5340.
Now we got a question from the testlab, about the transmit power parameter.
The setting in...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hello. I am using vscode. I added sdcard to broadcast_sink in the existing samples in applications/nrf5340_audio and checked the list with the serial monitor and wanted to...
We want the system to be in low power mode in idle state. Therefore after advertisement is sent the BLE is switched off using bt_disable. The return for this function is fine...
Hello, I am using peripheral uart as my base project and uppn that, I have built my application.
I am delibrately changing the flash region just to see if i can modify flash...
Hello, I can commission nrf52840 bulb by iPhone successfully using below QR code:
https://project-chip.github.io/connectedhomeip/qrcode.html?data=MT%3A6FCJ142C00KA0648G00...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
