Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Many DevZone tickets inquire about programming the nRF9160 modem firmware through the SWD interface using nrfjprog or other command-line tool on a PC. Several of those tickets...
I have set nrfutil to use the v2.5.0 toolchain:
burt@T420s:~$ nrfutil toolchain-manager list Version Toolchain * v2.5.0 /home/burt/ncs/toolchains/7795df4459 v2.7.0 /home...
I'm currently porting an existing NRF SDK code base to NRF Connect SDK (Zephyr)..
Our existing code used NRF_ATFIFO to communicate events from interrupts and multiple...
I'm working in an workspace application. The application was forked from the example application at version 2.5.2 and later updated to 2.7. I've been developing for several...
I'm currently porting an existing NRF SDK code base to NRF Connect SDK (Zephyr)..
Our existing code used ble_link_ctx_manager to maintain per connection state in a common...
I would like to get the events offered by the mfd driver for VBUS detect but for some reason my callback is never triggered. I'm doing this atm:
Devicetree:
Loosely...
HI there, I'm a bit confused with how the Data Mode would work for receiving data.
Our setup / situation:
UART connection with the nRF9160
Regular AT commands work...
Is there a way of detecting if NFC antenna is connected.
My thought process is, set as GPIOs, one as input and one as output set high to measure the continuity. Am I able...
I believe I'm having a similar issue to this ticket
I'm trying to connect to AWS IoT Core with an nRF7002DK by basing my work on the AWS IoT sample. I'm building the project...
Software version : v4.1.1
Hardware procured in month of June 2024.
Please suggest if any setting needs to be optimised to filter out the inital current.
Load current...
Hi Nordic,
We are planning to port our project from the nRF5 SDK to NCS v2.7.
Currently, we are using NCS v2.7 to build the firmware for our existing custom board based...
Hello,
I'm trying to use a SPIS peripheral from the NRFX library in a nRF Connect SDK 2.7.0 project. The reason for using the NRFX library is to clear a GPIO pin in the...
Hello,
I made a firmware that uses the IPC from the net core to the app core on the nrf700DK board.
I can read the events that generate callback on the receiver core ...
Hi, we are interested in the possibility of using CODED and non-coded (1MB or 2MB) PHYs simultaneously. Our design has an nRF52833 that will be used for connection from a...
Hi,
I need to fully take over the function HardFault_Handler
1. I overwrote the function: HardFault_Handler debug but did not stop in the function HardFault_Handler while...
