It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hello,
I'm getting started using the nRF Sniffer with PCA10040 and Wireshark on MacOS. I followed the instructions in the User Guide and was finally able to set it up by...
Hi
This is just a head's up. In function nrf_esb_pop_tx(void) you have the following code ...
Instead it should be the following...
Otherwise the bug is such that...
The Introduction page is inconsistent:
infocenter.nordicsemi.com/index.jsp
first it says
[quote]]The mesh stack is also compatible with the nRF52810 platform, but not...
Hi all,
As I've been researching, the mesh sdk is not supported on the nRF52810 SoC, although being compatible. Is there any development or plan in changing this? I'm planning...
Hi,
Is there any way to add conditional compilation in linker file?
I have two versions of a code, one with DFU and one without, i want to combine the versions. is there...
Hi everyone,
I used SPI interface to access a external flash with page size 256 bytes.
I found I can't access full page, because the maximum of one SPI transaction is...
hello all ,
controller nrf51822
i am trying to development for EPD 7.5 spi interfacing through external flash image send so how to set spi latch reset turn on parameter...
Hi, there
I try to use the nrf_atfifo in my program, but I found the atfifo cause hard fault in my program,below is how I use the at_fifo in my program.
and I also found...
Hello, I have a problem with my nrf52832 customised board
It has loaded the ble_app_uart example of the 15.2_SDK and It have the correct pinout from my board, These are...
1. I try DFU bootloader with OTA, it success.
2. But the Application was gone.
3. If item 2 is real, is that I have to porting the force enter to bootloader mode by botton...
Hi!
I am working on NRF 52840 Controller and Soft Device Version 6.0.0. Coding using Keil IDE in C.
Also developing using Free RTOS.
According to the requirement I need...
Hi,
My development environment is sdk12.3 s132_3.0 pca10040 I want to increase the MTU size to 64 bytes in nus. I programmed as below, but there is no MTU size change. It...
I have been trying to configure a single shot timer as a low power alternative to nrf_delay_ms().
I have my timeout handler configured to do nothing and the timer is created...
Hello all,
I have an ESRPB switch from EnOcean which uses the PTM215B transmitter internally.
I've factory reset the switch to its default state and have confirmed that...
