Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I am using nRF52840-MDK and connect to my Ubuntu running in VMWare. When I connect this device to my laptop and run pyocd-flashtool. I am getting a error message stating ...
Hi
I have purchased an nRF52832 DK to develop a human fall detection device. I'm a newbie to embedded studio, and nordic products. I just started to understand things on...
Hi, I have seen a few similar questions to this but the answers weren't too clear...I am trying to use both the long button push and the button push actions to generate separate...
Hello,
I have a Raytac MDBT50Q-RX USB dongle that I want to evaluate.
The dongle comes with Raytac's own test firmware.
In order to evaluate it for my purpose, I wanted...
I am very new begginer and dont know where to start about nordic nrf52832 chip. Started a week ago with downloading SDK and playing with examples in it.
I in specific need...
This is the structure.I am using bitfields here, even if i don't the problem still exists.
struct CODE_T
{ uint32_t guest_code_start_time; uint32_t guest_code_end_time;...
Hi,
Lior Neumann and Eli Biham found a vulnerabilitiy in BLE secure connections, to which CVE-2018-5383 was assigned.
Is the S132 SoftDevice affected by this vulnerabilitiy...
Hi Everyone
My requirements are as follows
1. I am running 4 tasks using free rtos in which one measures the ADC , 2nd sends the adc data over BLE and 3rd check if the...
hello
I am using sdk 15.3 example code of DFU (secure_boot loader \ pca10040_ble)
I want to debug code but i can not.I getting error like that "Error Flash Download Failed...
Hello,
I have been using this method for a while now and everything seemed to work. But for one of my device the method returns the error 0x3400. I wanted to know where...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
Hi there,
I want to do scanning existing networks and for these goals, I need to enable Commissioner on Commissioner side. I use the otCommissionerStart function but when...
I am looking for an example that can work with Android 6 and higher
Current examples on Github have compilation problems probably using older gradle.
The application need...
