hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
HI
When working on the NVS sample on a nrf9160 DK , I noticed the option CONFIG_REBOOT=y
However, it is not clear to me why this option is selected in this sample and...
Hi,
I'm a bit confused regarding the DFU process for the nRF5340: Under what conditions would the interface between the application core and the network core change?
I...
I am using the Nordic Semiconductor Power Profiling Kit II to measure the interval time of a periodic activity of a target device by monitoring the power consumption and measuring...
Our system has SPI and I2C. Each of these communications works in isolation, as implemented in our program, for multiple transactions. When we try to include both we noted...
On p. 62, section "5.3.10.1 Device startup times" of nRF52805 Product Specification v1.4, the startup time of the nRF52805 is discussed as a function of the capacitance to...
Hello,
We use nrf-connect-sdk v1.9.1 (Zephyr v2.7 LTS)
We have a set of network devices. Both routers as sleepy-end-devices.
The sleepy-end-devices connect to the...
how to set bt tx power in NCS
I referred to this example "hci_pwr_ctr", but err occurs:"Set Tx power err: -5 reason 0x00", Possible errors are BT_SCI-ERR_SUNKNOWN_CMD。 ...
Running NRF52840 mcu core on custom board using 17.1 SDK
1. Use the nRF Connect Mobile app to connect to our device over BLE
2. Run the dfu uploader to update FW from...
I am planning to modify the SLM application (NRF9161) to load its own certificates for TLS upon startup. This should be doable via modem_key_mgmt functions.
However, NRF5340...
Hello,
After migrating from NCS 1.8.0 to the latest NCS 2.7.0 version, I am no longer able to disable PRINTK , which we previously did to reduce flash memory usage, as we...
Is the nRF 5340 already FCC Pre-Certified ?
When we integrate the nRF5340 SoC within our product, should we need to get our product certified by FCC ? is there any difference...
hi professor,
The npm1300 is used for power management on my borad.When VBAT and VBUS are connected simultaneously, the bulk 2 output power supply varies between 1V and...
Hello,
I used VSCode debug for APP core without any issues.
But I cannot debug NET core because, APPROTECT is turning on. I want to disable APPROTECT persistently for...
Hello,
I freshly installed nRFConnect 5.0.2 in a Windows PC. Installation was fine.
When I start it I get an error:
How can I overcome this?
BR Matthias
