Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Hi guys,
I’m using nrf51822, s130 and sdk 12.3.0…
I would like to achieve that unknown peripheral won’t find my product or at least differentiate by device name while...
Can i use the bouder router used in thread example(on nrf52840) in the iot example to replace the Rpi bouder router so i can skip the tunnel setup(using hurricane tunnel)...
Hi everyone,
I have some questions regarding the use of EDIV and Rand in BLE Legacy Pairing.
What I understood from the specs is that these are generated during...
I think instead of releasing separate SDK for #BluetoothMesh, Nordic Semiconductor should merge #BluetoothMesh into #SoftDevice. Is it possible ?
If yes, then we can even...
We are using the nrf52840 with OPENTHREAD and would like to use the Nordic COAP application because block transfer and observe are implemented. We need to do multicast and...
Hi,
I have a development board nRF52832 and we are looking for 3rd party modules built on the same. I want some configuration changes on the modules.So, please someone help...
Hi
I am currently using SDK 12.1.0 with SD 3.0.0.
I want to add the option for serial DFU, which was added in SDK 13.0.0.
I wonder if I can implement the serial bootloader...
first of all many many thanks for nrf sniffer 2.0 and all of it's improvements (linux, live data display, easy install ... etc)
i'm sure there are still a lot details missing...
I am trying to use the nRF Connect v1.0 RC with the pca10040 board. I followed the instructions of your [page] and when i open the serial port i got an error (Error occurred...
I am using nrf52832_xxaa with SDK v11.0.I tried writing into the APPROTECT register by using the code below
sd_softdevice_disable();
NRF_NVMC->CONFIG = (NVMC_CONFIG_WEN_Wen...
Hi, as per subject, I would like to know the trade-offs of using the internal DCDC vs LDO when it comes to RX sensitivity specific to the nRF52840-QIAABB variant.
From this...
Hello,
I am using the nRF840 PDK for testing the radio communication.
During my tests, for TXPOWER=0xD8(at minimum), I found a gap of 7 dBm between the radio output...
Hi, I am trying to connect the nrf52840 to GPS module, and I hope that the dk could read the GPS information via UART. I try to modify from this example nRF5_SDK_14.2.0_17b948a...
Hi,
the following are the TX's current consumption for 0 dBm from the datasheet:
I assume the second line refers to the measurements when the internal LDO is used...
Hello,
I know how to update the application through OTA at the moment, I do the following steps:
set the device run in DFU mode by writing 0x01 in Experimental...
