Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
Hi,
I am experiencing an issue with the nPM2100 I2C communication when using nRF Connect SDK 3.2.3. My hardware is a custom PCB with nPM2100QEAA and nRF52840QFAA
I am...
Hi everyone,
I am currently working with the nRF9151DK using nRF Connect SDK v3.2.3 (Zephyr OS v4.2.99). I am trying to run a basic UDP sample with a Terrestar Solutions...
Using the 54l15 chip, with the NCSv3.2.1 version, the example is compiled using peripheral_uart.
I have been using this environment for over a year now.
1. When I was...
Hi there , would the nRF54LM20A support USB "host" or USB "OTG" using Zephyr stack?
I can see that the device includes the DesignWare OTG USB 2.0 controller ( snps,dwc2...
I have made several Build-Configurations for my device. These are using "Extra Kconfig fragments" and everything works a it should.
Now I saved the Build configuration as...
Hi Team,
I am currently working on the nRF52805 module and have developed an application that supports dynamic service creation (runtime GATT service creation).
During...
Hi folks, so I will start by saying I have had this device working at home under Windows 11. I have brought the device to work to use on my works computer, which is still...
Below is the relevant code and log:
SDK：v2.9.1
static void dfu_work_handler ( struct k_work * work )
{
int ret = bootmode_set ( BOOT_MODE_TYPE_BOOTLOADER );
LOG_INF...
Como faço para habilitar o registro de logs do mcuboot para visualizar os logs de atualização DFU no nRF Connect SDK 2.9.2, usando o nRF54L15 em uma placa personalizada com...
Hello team,
I attempted to measure the sleep current on the nRF54L15 DK board, but I’m seeing a very high current draw of about 74 mA.
I built and compiled the peripheral_power_profiling...
Hello,
We are developing a custom board that uses the nRF54L15 chip, and are trying to flash an application along with MCUBoot to allow for OTA updates. When I flash the...
Hi Nordic folks,
I'm trying to get the nrf54L15 in a Fanstel BM15M to go into the system OFF state and be woken up later by a timer. All the documentation I've seen says...
What's minimum hold time for a pin reset on nRF54L10? https://docs-be.nordicsemi.com/bundle/ps_nrf54L15/page/pdf/nRF54L15_nRF54L10_nRF54L05_Datasheet_v1.0.pdf doesn't state...
Hello, I am developing an application that uses Bluetooth Channel Sounding, and for that reason I need to have two devkits connected to my computer at the same time, but the...
Hi there,
I was designing an add-on development board to go onto the development kit to test a 1.8V application. I need VDD:nRF on the 54LM20 to be set as the same as VDD...
