Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
When using the nRF52 I was able to program the device with a special test build which allowed me, via a simple CLI, to control the radio and set a channel, vary power, set...
Hi Team
im trying to change device name during running time..
i can able to change the device name working fine for connectable mode...but if i go for running time non...
the power consumption is about 6.12mW in BT connected, and consumption is about 7.75mW in advertising mode.
is it normal or has possibility to reduce it to extend the battery...
Hi, you must be sick of me!
Now that (somehow) I've got the BLE Secure DFU Bootloader to work on my nRF52840 DK board. I'd now like to load it on a nRF52840 dongle pca10059...
Hello !!
I am using ble_app_becon example code to send some data with device name. On central I'm scanning and searching with device name to identify at central side and...
Heija Guys,
I have a question regarding the usage of the Zephyr BLE and the PWM. I would like to use the Zephyr BLE Stack and the PWM Driver together. The Problem now is...
Hi,
i am working on dfu with NRF52DK. I am facing a problem with compiling a example dfu code "pca10040_s132_ble_debug" .
error message is "cannot find ../../../../.....
Hi,
We bought 2 pcs of nRF52840 Dongles and want to use them to test if a nearby BT device has the correct MAC address.
I've programmed them with "sniffer_nrf52840dongle_nrf52840_7cc811f...
Hello,
I'm using the "usbd ble uart " with twi scanner example to send a sensor value through an arduino 33 ble sense using nrf52832 and it works very well . but when...
Hi,
I'm using the light switch example in the nRF5 SDK as base for Ble-Mesh. I'm using a nrf mesh app for provisioning. I have both client and server model in my application...
When building a project that works with the SDK 1.5.0, I get the following...
r@mint:~/ncs.1.6.0-rc2/nrf/nordic_assist/nordic$ west build -b nrf9160dk_nrf9160ns
[0/12...
I am working on a custom board for the nRF9160 and currently have a DK and a thingy.
I need to make a serial interface available on the DK, thingy and a custom board I...
I want send data from Mobile over established BLE Mesh Network (through Proxy node to all nodes in the network) and also get data from BLE Mesh Network.
Data is customised...
I have not set nrf5340 i2c2,uart2 to work .
,in prj.conf ,add below configure:
CONFIG_SPI=y CONFIG_NRFX_SPIM2=y
in prj.overlay ,add below configure:
&spi2 { status...
