I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi ,
I have the nordic nRF9160 DK and the Nordic Thingy:91. I am trying with the Asset Tracking application version : nrf9160dk_fw_2021-12-15_cfedfdfa, with the last modem...
Hello !
nRF52840 have " 128-bit AES/ECB/CCM/AAR co-processor (on-the-fly packet encryption)" what is expected to be used together with RADIO for encrypt/decrypt packages...
Hi,
I noticed that latest nRF Sniffer BLE version support importing IRK, however, I can't make it successful, do you have a step-by-step guide for IRK importing on wireshark...
i just have a quick basic question about the device driver API, why does the samples/drivers/i2c_fujitsu_fram application not use a device tree node for the i2c peripheral...
Hi,
I am not sure how to explain or try to recreate the issue but I'll try my best.
Tools: I have an NRF52832 Development Kit bought from Digikey Canada. I am using...
Hi I have a programmed the nrf52832 custom design board(not the Development Kit) with Ble Becon example code given with SDK and checked the power consumption. It consumes...
Hello
We have always been able to go to the certification test house and complete cert without any issues. This is the first time that is mandatory to run the test using...
Hi
We are using NRF_51422 dongle in our university for Labs development with students
We were able to setup & install the NRF_sniffer. It is working with the command line...
I have an nRF52840 + nRF5 SDK 17.1.0 project that has been running on S140 7.2.0 and we're getting ready to lock some things in. But we happened to notice that there is a...
Hi,
I use peripheral_hr sample code of V1.7.1 version to send Data HRM by Bluetooth. the frequency is 22 Hz only.
I would like to icrease sample rate to 2 KHz, could i...
Screenshot of error message
Hello, I've followed the steps required on YouTube for setting up VS code with nrf Connect for desktop and the toolchain manager. It didn't...
Hi Team!
Currently I an working on disabling JTAG/Debug and SWD lines to protect code from read/write through any JTAG debugger.
For this, I have used nrfjprog utility...
Hi Support team,
I am testing nRF5340+nRF21540 with MT8852B now. I come across two issues in running the DTM FW from nRF Connect SDK v1.8.0:
1. nRF21540 TX gain value...
hi， I'm working on passthrough firmware(nRF5_SDK_17.1.0_ddde560)，I need to increase the priority of the serial port,see following code,When APP_UART_FIFO_INIT priority set...
