Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Please don't give the usual response of 'try the troubleshooting guide' to flash the J-Link or Mbed firmware.
What I (and probably others) really need is the real initial...
I have this project where I have managed to build and flash my code onto the controller. I copied the example code from blinky (that didn't work) to my main.c and then I changed...
I created a simple driver call for UART transmission and when I debug the program and put breakpoints at every transmission, it seems to work fine (I see the characters sent...
Hi, If there is already a FAQ, Code or support ticket that I missed, I am more than happy to read it. I have done a number of searches but cant quite get to what I am looking...
Hi everyone,
I am interacting with the ble_app_hrs in order to learn about bonding. I am using nRF52840 DK as a peripheral and donggle (nRF52840) as central along with the...
Hi,
I understand the on_cccd_changed() will be called when CCCD changed. But I can't figure out which attribute it's associated with. I try to print out the UUID which is...
Hello,
I'm using the Azure Iot Hub example on a Thingy91 and am having issues with certs generated from a Linux environment. Everything works just fine with and without...
Hi ,
We are using nRF52832 IC for our project, Using BLE and PWM peripheral.
We are getting 1.28mA power consumption in the sleep mode.
As per the datasheet it should...
Hi, I built the lighting-app( Link ) and run on nrf52840 DK. Then, I tried to replace the serial shell console with RTT shell console. I append the configs below to the prj...
I am using my custom board , it is usually powered with a dc supply and I can program it easily. My chip is NRF52811.
When powered with a Cr2032 the segger studio says id...
Hello!
I have formed a Thread network and I am trying to ping an external IPv4 address and that request is not being forwarded to the border router.
My OTBR is a Raspberry...
Hello I am developing an application based on the "ble_thread_dyn_mtd_coap_cli" example. To create a Thread resource, I see that the "otCoapAddResource()" function is called...
Hi,
we are using NRF9160 based Custom board with Zephyr,
I want to track the Current time in IST format and i need to generate an event to DPPI on particular time (ex...
I might be missing something obvious here, but when the device is flashed (via SES), the application works correctly. When the device is power cycled or reset due to the watch...
