Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello, We have been using the PCA100059 version 1.0.0 dongle with a custom firmware which fails to run on the new PCA10059 version 1.2.0. Unfortunately there doesn't seem...
Hello,
Im a beginner in microcontrollers programming, just started with the pca10056 and pca10059. Im aiming to develop a beacon scanner for pca10059, to send data via usb...
I compiled and debugged the PCA10040e ANCS example (ie emulating the 52810 using the 52832) from SDK 15.3 - successfully. But I wanted to turn off code optimization to facilitate...
Hello,
As many mobiles do not have NFC I would like to use LESC OOB pairing with an QR-Code which could be shown on the device terminal. Well, I know where the NDEF message...
SDK version :15.2
question； when i use app_timer , i got interrupt which is not i wanted.
i creat and start timer :
app_timer_create(& m_timer ,APP_TIMER_MODE_REPEATED...
I'm using nRF SDK V15 with nrf52DK board, running the ble_app_hids_ms example.
I I want to have continuous non-stop advertising duration, should I have both APP_ADV_FAST_DURATION...
Dear Sir/Madam,
My question regards the behavior of the EasyDMA during the transfer of data to / from a serial peripheral like SPI or UART.
Let's suppose that during the...
Hi all,
I using SDK 15.1 and 15.3 for test.
I am working with DFU for NRF52810.
I tried success for NRF52840.
But I can't update success for NRF52810.
Below is scrip...
I use the Firmware «AT host sample» on Thingy91. Then I connect to Swisscom network on band 20. The current consumption is about 3.5mA. Then I send AT+CFUN=0 or AT+CFUN=4...
Hi All
We are using nRF9160 DK, and we are working on ADC channel. we use This example of ADC. I am using single-ended with no over-sampling with a gain of 1/6, reference...
Hello
my setup is sdk 15.3, nrf52840, s140, open bootloader and an application.
Everything is merged, flashed and running and no changes are made at the standard addresses...
I am currently developing a peripheral app on a custom board with a nrf52832 chip on it and connecting to the device using QT's ble library. I'm having issues where my connection...
I want to turn on /off LED by advertising TX of BLE
peripheral : nrf52810 central : nrf52840 Specifically, peripheral performs advertising TX, The central processes LED...
