Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello All,
I implemented the HTTPS call to Amazon using the certificate, and the POST request returns the device ID. Like you docs: Exercise 2 - Adding TLS to the HTTP connection...
HI
My current system consists of an nRF54L15 paired with an external flash and sensor. In low-power mode, the current consumption is approximately 15 µA. After sleeping...
Hello! I am facing issues when trying to set up a PPP connection using the Serial LTE Modem (SLM) application on the nRF9151 DK, and I would appreciate some guidance. I am...
Hello,
I have seen many topics regarding the SAADC sampling modes and power consumption trade-offs on DevZone, but none of them clearly address my concerns. I would like...
Hi there,
We are currently developing a system, where around 480 kbytes of data are transmitted over BLE. Throughput is supposed to be as high as possible.
We are using...
I have a school assignment revolving a technological product, where i need to ask a few questions to a business about their involvement with the product. Therefore i need...
I set the voltage at the PPK “Source meter” to 1250mv, and then used a multimeter to measure the voltage between the PPK “vout” and “GND”, which was 2830mv. How can this situation...
Hi,
We're working on a cellular design using the nRF9151 with an nRF7000 for location finding. We have a working prototype on the Thingy91x and are currently focusing on...
I was reviewing the Large scale Bluetooth mesh testing - Blogs - Nordic Blog - Nordic DevZone and noticed the statement: " Initialize the network by flashing the test firmware...
I want to connect Waveshare E-ink display to nRF5340 using e-Paper Driver HAT. At first, I tried to make all the calls by my own, just by rewriting the code from the ESP driver...
I am attempting to use the COMP section to build a relaxation oscillator. There appear to be a number of interactions between sections, some of which are subtly documented...
Hi there,
I went through all the documentation and instructions in order to use my nRF52DK as a sniffer and I can not see it in the capture devices in wireshark.
am not...
1. What versions of GSMA specification does nrf9160-SICA modem support? In particular we are interesting in SGP.02, SGP.22 or SGP.32 versions.
https://www.gsma.com/esim...
We are developing a Bluetooth peripheral device.
The peripheral has no input/output capability, and a fixed passkey is pre-programmed.
We would like the pairing to succeed...
On the Online Power Profiler I noticed changing iDRX interval has a significant effect on power consumption. How can I adjust this interval on our device?
I saw this ticker...
