hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi I am wanting to use the ARDUINO 4 RELAYS SHIELD with the nrf52480 or at least see if its possible.
https://store.arduino.cc/arduino-4-relays-shield
relay data sheet...
I wanna use nRF52820 to make some application development.I wanna a sing-board development kit for nRF52820 ,and nRF52833DK supports development on the nRF52820 SoC and nRF52833...
Hi Everyone This is my first time designing a PCB with the NRF51822. I have designed it using an 2450AT18B100E Antenna and a BAL-NRF02D3 balun. Below is my schematic:
...
There are discussions on WLCSP light sensitivity for nRF5 product, which affects RF, clock accuracy, and low power current draw etc. what about the nPM1100 which clock accuracy...
Is my understanding correct that with VDD supplied and ENABLE = high, having VDD_GPIO floating (i.e. disconnected from a regulated 3.3 V supply) is a valid state? We intend...
hello Nordic
i am working with nrf52840 sdk16.0 s140
i wish to read the UICR register value like this :
but i get this compilation error
since it is a define...
Hello, I'm working the nrfx saadc legacy driver, and despite changing whether I measure Vdd(on the dk) or GND, the saadc output(p_event->data.done.p_buffer[0]) oscillates...
SDK14.0+NRF52832（PCA10040 demo board）:
I want to add static passkey to avoid MITM attack， I write code as following, but when I use the mobile app ‘nRF Connect’ to connect...
Dear community,
I need to operate a BM833A as I2C slave and to do so, I performed the following steps:
I modfied my sdk_config.h and set TWIS_ENABLED and NRFX_TWIS_ENABLED...
Hi,
I used nRF Connect for power profiler and programmer for hundreds of times.
But since today, it just keeps on showing white screen.
I tried "Ctrl + R" as well as...
Hi Team,
We are using the NRF52840 SOC for our development purpose and in our application we are planning to port the RTOS.
Could you please suggest us which RTOS is...
HI,
I am using the central_hids project in NCS V1.5.1 on NRF52840 , and now i want to add USB hid into the project, how can i do it?
I have try to do it in nrf_desktop...
Hello,
I've been trying to learn to develop an app based on ZigBee, it's the first time i'm working with nRF hardware and the only things i've done so far was to run some...
Hi,
I am currently trying to embed the ATT_MTU throughput example on two nRF52840 dongles. The main issue I am facing is that after I compile and program the hex files onto...
