I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hello,
I have a security issue with a product with nr52840 because if a hacker connect to my device with nrf toolbox for example, when i stop the bluetooth connexion on...
Hello, I've been working with unit tests lately, and got the example unity project to run (from here ). Now I encounter some issues when integrating it into another Zephyr...
I use usb with secure bootloader to flash 52833/840/832 boards. Is there a way to use the nrfjprog --memwr/rd over the usb after a DFU on USB upgrade to new app?
Steps w...
Hello,
I have an analogue audio mic connected to external ADC. The external ADC can give an output of 16bit, 20bits, 24bits and 32 bits I2S data. I have configured to send...
All the SDK health device examples appear to have a rather complicated relation between the BSP buttons and the behavior of the device (advertising, connected, etc.) which...
Hi Everyone,
I am having some trouble on nrf5380 PDK. I can not connect it to my PC.
I attached photo of nrfconnect.
There were 3 serial ports but I have used just one...
when using the TIMER, I set the TIMER's time_ticks=53328 which means that every 3.33ms, the TIMER will call its callback function and start ADC sample. However, when I use...
Hi.
We are evualuating and testing NRF9160 DK and after a while testing and reading different threads of the forum I know the mode GPS + LTE in the nrf9160 only work in...
Hi. I'm using external board with nRF52832 and GPS. (SDK15.0.0)
I used ble_app_uart example and succeed in receive data in my nRF UART v2.0 app.
I got this kind of data...
Dear all, Im experiencing the following error that pops out on RTT console during the first few lines of main():
I understand the definition here: https://infocenter.nordicsemi...
This is my code:
This is the results of the logs in the code:
<info> app: tx buffer length = 8 <info> app: AA <info> app: FF <info> app: 10 <info> app: 08 <info> app...
We are using an MX25R6435FZNIL0 part on a design with a nRF5340 module and wish to test that 48MHz operation of QSPI is working, we are using the latest master version of...
I am using Keil and trying to debug one of the examples in nrf_SDK_12.3.0 and half of the lines are not accessible in line by line debugging. Those lines where one can set...
