hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
I Have been trying to interface mpu6050 with nrf5340 DK .
f ( NOT "${ret}" STREQUAL "0" )
message (FATAL_ERROR "command failed with return code: ${ret}" )
endif (...
Hi,
I'd like to know what is the cause of the stall in
sym_E5Q6O4GY4KO3GMW7WJYXLZKHO7ZGDWLU4ZPAKWA() at 0xa55a
when calling sdc_hci_cmd_le_set_adv_enable ?
Here is...
I am currently considering the use of an external Flash IC for a Matter device.
I have two questions and would appreciate your help:
1. Is the MX25R6435FZNIL0, which is...
Hello,
according the datasheet the nRF52832 has an gain error of 0.02%/ ◦C and E_G1 of -3 ... +4%. This is too high for our requirements. Is there a way to improve this...
Hello DevZone,
I'm developing a HomeKit project for the customer. They require 2 BLE advertising in one device. One advertising is for HomeKit over BLE, and the other one...
i want to switch between two code... the code is simple led blinking i am trying for the testing purpose...in my code 1 led1 is blinking 500 ms of delay and in my code 2 led2...
So from my understanding from the zephyr documentation, if I want to use 7 bit I2C addressing, don't set I2C_ADDR_10_BITS. I am wondering how I can make sure this macro is...
Hi,
How do I add the System ID characteristic (UUID 0x2A23) from the Device Information Service (DIS) using Kconfig commands in the prj.conf file?
For example, I can add...
Hello,
I am having a strange problem with nRF Connect SDK for VS Code, and would appreciate some help.
I don't know what I did, but suddenly I am not able to "Generate...
I am developing a product that uses the chip of NRF52832 and runs FreeRTOS on the chip to manage my task list. However, I found that the program would be stuck in the idle...
I've got a custom board that uses an nRF52832. Firmware was built with NCS v2.6.1.
My hardware uses a MIC826 IC for ensuring the nRF52 is held in reset whenever the power...
I'm looking for a beginner's guide to setting up external flash on the nRF9161 DK. I saw nRF Cloud Multi-service as an example, but its docs did not explain what was needed...
Hello,
I have had posted several times over the years and solved a problem or two. I find it very thorough to finish out a post by concluding my findings. This said, I...
Hello everyone,
My problem is that I could not flash one of my NRF5340 Audio DK boards, the program that is installed before was headset configuration right. I am using...
We wanted to share our feedback as we recently went through Zigbee 3.0.1 BDB/cluster certification using the ZBOSS with our end device product. While we were ultimately able...
