As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi There.
I been 15 year experience in embedded system development but I'm very new to the Nordic nrf environment.
I'm eager to learn and develop some product and provide...
Hi, I have a nrf54H20 board rev 0.9.2 and I followed the https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/app_dev/device_guides/nrf54h/ug_nrf54h20_gs.html#nrf54h20_dk_bring...
Hello, We are currently working on designing a CS-based distance estimation algorithm, referencing the two example routines, `ras_initiator` and `ras_reflector`, from NCS...
I'm getting exactly the same as this ticket now I've switched to extended advertising. Was there any resolution?
Android is fine, iOS 18.5 phone sits in a connect/error...
I'm testing the spi communication protocol with the nRF54L15 DK. At that moment, I'm testing the lesson5-exercise 1 solution of the intermediate course. The problem appears...
Hello,
As the title, I'm using nRF5340 audio sample to test Walkie Talkie demo.
I know that in nRF5340 audio DK, the microphone is set through CS47L63. Now I want to use...
Problem originally due to installation and failure of Gas Smart meter - a common problem in the UK with up to 4+million similar customers. Issue is Smart meters on external...
It isn't clear from the nRF5340 documentation and the only related post doesn't answer it but if we want +3 dBm output power, do we need to wire the nRF5340 in high voltage...
I have a mouse that is advertising, and I paired it with my host. It always stays in connected mode. When I press the three buttons — middle, left, and right — for 5 seconds...
What is the recommended termination for unused RF pins on the nRF54L15 in QFN48 (QFAA) package? Can you confirm this is acceptable?
ANT Pin 31, floating VSS_PA Pin 32, grounded...
Hi, I want to change the voltage of the VDDIO in the group of pins labelled Port 1. I launched Board Configurator from nRF Connect for Desktop but it says "This development...
I have code set up to configure Timer3 to generate a Compare event at 100 KHz, using the PPI so that triggers an ADC Sample event for the two enabled ADC channels. EasyDMA...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hi,
I'm developing an application with a custom firmware image for both the nRF52840 and nRF9160 on the nRF9160DK. I've always been on ncs v2.5.0 and decided it would...
