I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Hello everyone,
I'm unable to perform DFU over SMP BT with nRF Connect for iOS. I've already verified the process works with mcumgr (Ubuntu 20.04 LTS) and with nRF Connect...
I am trying to use the `fmfu_smp_svr` sample project, as described in nRF9160: Full modem firmware update using SMP Server , to perform a full modem firmware update.
The...
Dear ,
I am going to use SDK 17.0.2 spis example.
But I found it is 8 bit data width. I am going to use 16 bit data width .
Would you teach me how to change?
Hi all,
I am using NRF5340, and I want to use pin 0.14 for spim. However, I found it was used by QSPI, in zephry.dts:
So how can I close QSPI to use pin 0.14 freely...
Hi.
Below is used the same schematic for nRF52805 but with different placement for RF components.
What are the pros and cons of each one? Is there one that is "better...
Hi !
I want to successfully send CTE after the CRC of the broadcast packet by operating the RADIO register under the Manual configuration of NRF52833。At present, I can successfully...
Hi developer,
I am trying to understand Beacon behavior and program. I am using BLE_Central multilink example to get informaiton from Beacons.
I added the below code...
Hi, I tested the (mcu_boot + smp_svr) example and can run dfu successfully with nrf_connect application. (Follow the page: developer.nordicsemi.com/.../README.html) Now I...
Hi Nordic,
One of my custmer want to develop multiperipheral product(The device connect to two central devcie).
The nRF52832 can certainly meet their requirements, and...
After connecting nRF9160 DK v0.8.2 kit and connecting the terminal, I observed the following messages:
***Booting Zephyr OS build .2.6.0-rc1-ncs1 ***
SMS sample starting...
Hi there,
We were using the Cryptographic library provided in the nRF5 SDK, with Oberon backend, to implement EdDSA/Ed25519 signing on our nRF5832 devices.
We are now...
Hello all:
I've developed an nRF52810 application based on the Blinky example. It includes buttonless DFU support and i'm able to update the firmware by an nRF52 dev kit...
I have a problem here with using saadc of nrf52832 .
The nrfx_saadC_init (), nrfx_saadC_channels_config (), nrfx_saadC_SIMPLE_mode_set (), and nrfx_saadC_buffer_set () functions...
