Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
We want to have same key for handling accept for LESC pairing and sleep mode if BLE is in advertising.
The implementation is based on ble_app_hrs_pca10040_s132.
...
Hi There
I am debugging my application board by light-swtich server project of Mesh example and " pca10056_s140_ble_debug " project of SDK example dfu.
My application...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
Like the subject, I'd like to change 'ble_app_hrs_c' and connect it to my device.
I changed the service...
Hello,
I am running an application on nrf52840DK. It is using uart service to send a sensor data through BLE to Uart servic on smartphone. I want to measure the current...
Hello,
We just noticed that according to the Raw data detail in nRF Connect, we are able to advertise more than 31B data limit. Is that possible or do we incorrectly count...
Hello,
I am trying to figure out a way to configure the adc node using the .dts Device Tree file in a similar way to what is done for other nodes such as &spi and &i2c....
I've installed the nRF Connect SDK Master manually since I need the Zephyr modules for a school project. I've manually installed the SDK before without issues but on my new...
Hi Dev team,
I am working with a nRF9160DK board. I am currently getting an error while building my SPM folder in : C:\Users\adeel\ncs\v1.3.0\nrf\samples\nrf9160\spm.
...
Hello!
I'am from austria and try to connect a Thingy:91 to your nrf-Cloud. First I tried it with your
iBASIS sim-card, but in austria we can't use this card.
Then I...
Hi all.
I did a layout with NFC antenna with a nRF52832 chip.
In the schematic (suggesten on datasheet) I have antenna coil with 2 capacitors to ground.
Drawing...
Hello everyone.
I would like to set-up a mesh network of Thingy:52 devices and an nRF52840, which would help me communicate from the an external stimulus to the phone, via...
I have an application where the nrf52840 dongle is hooked to a sensor. The sensor drives a pin high, the mcu grabs data from the FIFO (SPI) and puts it in a buffer. So far...
Hi Team,
We need to use Flash as EEPROM and we have the following queries,
1. How much maximum size of Flash can be configured/emulated as EEPROM/NVM?
2. Whether below...
