Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I am writing a basic health device application, It starts, loads saved data, starts advertising, takes measurements, if a connection occurs the data is transferred, other...
I have compiled the example application ncs\v1.4.0\zephyr\samples\boards\nrf\system_off configured for the nRF52dk_nRF52832
This example consumes 450-500uA (SB9 cut)......
Hello Nordic support team,
We are making product relate to battery service.
Tool and SDK: - nRF5_SDK_17.0.2_d674dde
- SEGGER Embedded Studio for ARM Release 4.52c
...
Hi, I am doing some development in nrf52810. where i want to use BUZZER to produce TONES
I am using SDK17.0.2 SES
I want to create tones instead of just beep sound in...
I found a fairly cheap (<$5) FCC certified NRF24 module with 20dBm output power. NiceRF RF2401F20 ( https://www.nicerf.com//product_180_216.html )
The FCC ID is 2AD66-RF2401F20...
Hi,
I would like to know security related libraries available in SDK 17.02.
Libraries that I found
1. Peer manager
2.crypto library
I would like to know is there...
Hi,
I got problem with Implementing the FDS example code as below, which I using is SDK nRF5_SDK_17.0.2, and always got error "FDS_ERR_UNALIGNED_ADDR", Already searched...
nrf5 SDK 15.20
Mesh SDK 3.0.0
nRF52832
Hi,
I am using nRF52832 and mesh stack , i want deliver temperature data through Mesh network.I look and run light-onoff &...
Hi Folks,
I would like to configure an UART RX pin as input GPIO as well as keeping it as dedicated to the UART peripheral.
I would also like to know if I can configure...
Using the current nRF connect v3.6.1 Getting Started Assistant I've managed to get everything installed to the point of using west to install the complete nRF Connect SDK...
This thread discusses the nrf51 devzone.nordicsemi.com/.../current-consumption-when-using-rtc-ppi-and-gpiote It says that the PPI (for nrf51 chip revisions up to rev 3) keeps...
Hi,
What is the used coding scheme in nRF Connect for Mobile when advertising on Coded PHY? Is it S2 or S8?
Should be clarified in the screen below
Thanks,
Lu...
In this PDF: https://infocenter.nordicsemi.com/pdf/nwp_037.pdf
On page 28 it says:
Active components on the PCB cause wideband noise coupling to the antennas. Verify that...
We have designed a board using the nRF9160 SiP and LWM2M. When testing with poor network connection (~ -118dB) we experience a strange behaviour. From monitoring the current...
