Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
I am working on nrf52832 and SDK V15_3 and Softdevice S132 . I want to enable 2MBPS mode to achieve maximum throughput. I have checked different links in nordic devzone but...
Hi , I succeed to flash the firmware to Thingy52
you can see the attached 2 pictures one is for the nRF Mesh app and the second is the Thingy 52 (Four units) which are ...
Hello,
I am using nRF52840 DevKit, SDK 16.0.0 and SoftDevice 113 v701
I am looking at nrf_bootloader example and want to configure a watchdog that keeps running even...
Hi,
I'm wondering what is a good way of keeping track of when the device is inside the active time window so that the data is being sent at the correct time.
Here is my...
Hi,
I'm working on two projects, in the first one, nRF52832 (softdevice S132 V6.1.0) is used as a slave component communicated with STM32L4+ over UART and the second one...
Hello,
I have been using nRF52840-DK and also nRF52840 Dongle for testing and I found an interesting behaviour when I established my test setup. The RF module acts as an...
Hi All,
We have a product based on nrf52832 that has a custom ble service with 2 custom characteristics.The first one is to send data to the nrf device and the second one...
Hi
I opened the Watchdog in the user application,and do nothing in the bootloader.Then when I use DFU,the CPU reset appears.How can I to deal with it?
And when I upgrade...
Hi
I am looking for some specific contract developer help to build and Android app to update Firmware in devices using DFU and the buttonless service. Obviously there are...
HI,
We are evaluation the nRF9160 in the devkit and we are trying to obtain the values specified in the nRF9160 Product Specefication v 1.1. After following the different...
We are creating and application that will use the Serial port to communicate to a host using an RS485 protocol. We have it working in SDK 15, but we are now trying to build...
Hello All, I want to generate Bi-Phasic two PWMs with 180 degree interphase delay and variable Duty Cycle with variable frequency upto 250 Hz in nRF52810 SoC. Can you please...
Hello, how can I use the functions in nrfx_twim.c
Using SES and the CMSIS config wizard, I have picked:
NRFX_TWIM_ENABLED 1
NRFX_TWIM0_ENABLED 1
NRFX_TWIS_ENABLED...
Hello
I wonder how to verify that teh scan response data is set correctly and if there are other parameters I need to set to get it working.
So for setting length i have...
