I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi, I've noticed a strange behavior of my device. I'm using a nRF9160-based custom board with nCS v2.6.0 and modem version 1.3.6. Long story short - after trying to acquire...
1.
2.
Hello. It is under development as nrf7002.
I'd like to ask you about the quasi-board configuration I saw in the sample example.
The target board in...
Hello everyone,
I am currently using Nordic NRF5340-DK board for development and I have run the zephyr UART driver sample that works an echo bot. This sample works fine...
nRF 52832 DK advertizes successfully .
But the name of the DK is not listed in nrf connect for mobile app. Peripheral_UART is the sample code that I have compiled.
Hello,
I am currently on a project where we have 4 BLE peripheral devices equipped with NRF52840 connecting to one BLE Central, which is an app on iOS or Android. From time...
Hi,
We're planning to integrate ble_app_uart and ble_app_uart_c into our project. Before integration, we tested the ble_app_uart example code on one development board. After...
Hi all,
I'm trying to get a UART connection running at 460800 bps, and it fails about 1-5% of the time, meaning that I receive less bytes than I expect. This happens a lot...
Hi,
I want to debug [i.e. attach to and single step] mcuboot [running as second stage bootloader] using Ozone and JLink.
I can connect to the board via the debugger...
Hi! I am trying to sync the time on my nrf9160dk with date_time_now() or date_time_uptime_to_unix_time_ms() but it seems that they return a very low unix_time_ms (only 1089262423ms...
The nRF7002DK board has a Vdd of 1.8 V, unlike every other Nordic board I've seen which use 3.3V. I assume this is due to the nRF5340 errata that state that the QSPI bus ...
Hi,
We are Designing the Long range module using nRF54L15 with nRF21540 FEM.
Now want to use Dual Antenna simultaneously. we have Couple of questions
Please guide us...
Hi all,
I am currently working on a personal project with hundreds of nodes. I have created a device with remote provisioning models (server and client). In my network...
I'm encountering an issue while trying to use the CAF LED module with the nPM1300 PMIC. Despite configuring the Device Tree, prj.conf, and led_state_def.h, I'm still getting...
I would like to confirm if my understanding is correct regarding calculating the average current consumption using the PPK2.
As shown in the image, the Selection Average...
I can't find any mention about MU-MIMO in the datasheet. Does the nRF7002 support MU-MIMO TX and RX?
I cannot find any details of if support is mandatory for a 802.11ax...
