Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I have tried compiling peripheral_hr in Zephyr, as well as flashing the heart rate demo binaries.
All give the same result - the board simply resets as soon as BLE Advertising...
Hello,
I'm trying to connect as fast as possible two devices (central : 52832 S132v5 and peripheral : 51422 S130v2), for a given advertisement interval. The central will...
People tracking and fitness trackers. Hello. Sorry for beginner question. I trying to develop a real time location system to track people (using rssi) and take data from their...
I'm attempting to perform DFU with the secure bootloader (bonding not required) and it is hanging after starting the update. Here's the log from the firmware (SDK 16.0.0)...
Hello,
I am developing an app which connect to provisioned node using GATT in the mesh network. But the limitation of this is, it has only pair to pair communication. It...
Been beating my head against this for a couple of days and came across a number of people on the forum with the same issue without a solution, so hopefully this saves someone...
Hi all,
I have some issue setting up the advertising data on my nRF52840 Dongle. I'm using the ble_template to develop my software and in my application i need to fill all...
Hi all,
can i send a scan request from an nRF52840 dongle using the nRF Connect - Bluetooth Low Energy software? I need this during development of my application where i...
Hi
I am seing framing errors when receiving using UARTE.
It is not external hardware, I have checked with different other interfaces and measured timing, no problems there...
Hi
I want to ask a few question.
When the phone sends a specific signal after connecting to the MCU, the MCU is sending data in real time.
When the power is turned...
Hi,
I was trying to find out if it is available to have authentification before connection and I found this link and it makes sense to me but that Q&A has been over 4 years...
Hello!
I use Zigbee CLI example and multi_sensor example on nRF52840. (examples/zigbee/experimental/cli/cli_agent_router and examples/zigbee/experimental/multi_sensor) ...
I have nrf52840 dongle and sdk nRF5_SDK_17.0.0_9d13099.
I would like to know, is there is an example in which, Advertisement Data is stored in flash memory and reading and...
I USE 9160 with i2c ，send data. then it tips :
[00:02:07.716,918] [1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0[0m
what is wrong ?help me ,thank...
